Question about 2000 Chevrolet Blazer

1 Answer

Power steering pump

My power steering pump went out and i was tring to see if i could get some information on the best way to replace it i nerver done it before and it is very diffcult to steer my the truck there is no leaking any where can some one help me

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 341 Answers

You have to remove the whole bracket with pump. then you need a power steer pump pulley puller then remove 3 bolts the same tool will put pulley on

Posted on Oct 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi all.I have asked this question


The Meriva has a known fault with the electronic power steering rack which causes some weird other issues.
The replacement part and labour is expensive - I had one and the price in the UK was around £1200 for the repair.
Thankfully we had a media push in this country and the pressure made General Motors (Vauxhall/Opel/Chevrolet) do the fix for free, try calling your nearest dealer and see if they'll do this for you Meriva 02 09 Power Steering Problems

Aug 16, 2016 | Cars & Trucks

1 Answer

Power steering pump 2007 Ford Edge located where? Can't seem to locate it..need to replace it; 3.5 engine


CAUTION: While repairing the power steering system, care should be taken to prevent the entry of contaminants or premature failure of the power steering components may result.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
  1. Using a suitable suction device, siphon the power steering fluid from the power steering fluid reservoir.
  1. Remove the RH inner fender splash shield. For additional information, refer to Section 501-02 .
  1. Using the special tool, disengage the power steering pump belt from the power steering pump pulley and position it aside.
    • Install the removal tool between the belt and the pulley and turn the crankshaft bolt clockwise to disengage the belt.
  1. Remove the 4 bolts and position the driveshaft aside.
  1. Using a suitable jack, support the rear of the subframe.
  1. Remove the 2 nuts, 4 bolts and the subframe support brackets.
  1. Remove the 2 middle subframe nuts.
  1. Lower the rear of the subframe.
  1. Release the clamp and disconnect the power steering supply hose from the power steering pump.
  1. Disconnect the power steering pressure (PSP) switch electrical connector.
  1. Remove the power steering pressure line fitting banjo bolt and disconnect the line from the power steering pump.
    • Discard the 2 seals.
  1. Remove the 3 power steering pump bolts and the power steering pump. This is a job best left to a qualified repair shop !

Jul 26, 2016 | 2007 Ford Edge

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

1 Answer

Replaced gear box and power steering pump,steering still not right


if you want an answer to assist you make a decision , a statement of "steering still not right" means nothing at all
comment on what the steering was doing before the pump replacement, after the pump replacement, what you expected
do the wheels wobble at speed , make ,model of vehicle number of mules done
All this information helps get a good answer

Sep 14, 2015 | Cars & Trucks

1 Answer

How to replace the power steering pulley on 1998 Cadillac Deville pulleyonly not the pump


sometimes it can be done on the car, but special puller is necessary. special tools are necessary even with the pump removed. if you don't have them, don't even try.

Mar 08, 2013 | Cars & Trucks

1 Answer

Ny Nissan Xterra power steering became stiff without any sign


Check condition of pump belt and check for correct tension. Have a pressure test done on the pump to ensure correct operation

Feb 11, 2013 | 2002 Nissan Xterra

1 Answer

Where is the power steering pump on 2002 chevy venture


You can see the power steering pump on the front
of the motor

It along with the alternator ,crank damper & sometimes
water pump,are driven by the same belt ,been that way for
a century

Oct 12, 2012 | 2000 Chevrolet Venture

1 Answer

I have a 2003 dodge caravan and the power steering went out what must I do what will it cost to fix this problem, and how long can I drive the car like that R obert N Reese


The power steering pump could need to replaced, or it could be a just a matter of replacing seals and rebuilding the pump. Cost will vary according to what work must be done, and I recommend that you get at least two estimates before you commit to repairs. You can drive the van without power steering for as long as your arms can stand it.
BillB

Feb 12, 2010 | 2002 Dodge Grand Caravan

1 Answer

Power steering pump replacement procedure


Check the autozone.com website and register the car. It doesn't cost anything and will give you access to an online repair manual for the car. The information regarding the procedures for changing the power steering pump should be available there. Hope this helped and best wishes.

Aug 29, 2009 | 2000 Dodge Grand Caravan

2 Answers

Power steering pump


your serpentine drive belt could be slipping over your power steering pump. Sounds like a premature failure from your pump. This is not an easy fix depending on the location of the pump itself. Remove your serpentine belt, locate the pump and pulley. Try to spin the pulley by hand. If there is alot of tension, your pump may need replacing. If not, try replacing the belt and check your belt tensioner for looseness.

Jul 07, 2008 | 2000 Chrysler LHS

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...