Question about Hyundai Motor 2003 Elantra

1 Answer

Changing headlight on driver's side

My lightbulb for my headlight is burnt out. I need to replace it. I bought a new one. There are two clips attaching it to the top, I unscrewed them. The headlight won't move.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 53 Answers

There is a 3rd bolt at the bottom of the lens assembely it is hidden under that open tube looking thing pull up on the tube and u will c the 10 mm bolt

Posted on Oct 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Head light have low but when using high does not work just on one side drivers side


HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Dec 20, 2015 | 2004 Nissan Sentra

1 Answer

92 Toyota Camry Passenger side headlight only works with HigBeam


You need to get a volt meter at the headlamp plug (Wiring harness) to see if you got a ground, power from the low beam wire, and then power from the hight beam wire. It's the best place to start.

May 13, 2010 | 1992 Toyota Camry V6

1 Answer

MY HEAD LIGHT ON DRIVER SIDE NOT WORKING


If it keeps blowing up fuse then you need to check the wiring and make sure the fuse is rated at the correct amps.

Aug 26, 2009 | 2000 Ford Focus

2 Answers

Lightbulb driver side 2008gmc 3500 6.6l


how to change driver side headlight bulbs?

May 30, 2009 | 2008 GMC Sierra 3500HD 2WD

1 Answer

Daytime running lights do not come on


Hiya...
When this happens, it means one or two of the halogen headlight bulb(s) has been burnt-out.
Do this quick and easy self-test:
Turn on the headlight switch to LOW and see if you see one (or none) turns on...you'll know one or two lightbulb(s) need to be replaced....this is why the green headlight logo flashed to tell you that a bulb has just burnt-out.
You'll need to remove the 4 black plastic clips that holds the top grille bracket frame onto the top metal frame that's facing the top radiator area.
If you know which headlight's bulb need replacing, just remove the 3 bolts...two are on top and one is by the side (close to radiator area)
Then you pull the grille toward you gently to allow your hand to access behind the grille and headlight area to reach the white socket that's connected to the headlight bulb.
This requires some patient as it's a tight area for your fingers to wiggle the socket off.
When the new lightbulb is installed, the green headlight logo will appear in the instrument panel when you start the engine.
That'll help!

Jan 24, 2009 | 2005 Chevrolet Equinox

1 Answer

Passenger side head light


glad you asked , its like a saftey pin , you push in on the lower side of that paper clip looking device , as you push in , move it side ways to the left or the right , depending on how your looking at it , its real dumb , just like a saftey pin . by the way there is a recall on the 2002 , 2003 altima headlights , if you see burnt connectors , or crumbly plastic were the actual bulb inserts into the light assembly , take it to nissan , under the headlight campaign , more often they will replace both headlight assemblies , all nice and new and clear . 2 thumbs up !

Jan 13, 2009 | 2002 Nissan Altima

2 Answers

2005 kia spectra - How to change the headlights out


I imagine that the 2005 Kia Spectra is very similar to our 2004 MY (mid year) Spectra. On the driver's side you first must remove the cover that extends forward from the battery. There are three plastic screws across the front and one screw on the left (as you face the engine compartment) attaching the cover to a bracket. Remove these screws and set the cover aside. The passenger side has no such cover to remove. For either headlight, there is a cup-like cover approximately 3 to 4 inches in diameter. Unscrew this cover (counterclockwise); I think you only need to turn the cover ~ 1/16 of a turn for it to come off. Set the cover aside. The connector is held in place by a spring-loaded clip that looks a bit like a bent paperclip. Press the end of the clip in and then away from the body of the connector. This will release the connector and the light bulb. Remove the old light bulb by pulling it straight out. Plug the new bulb in. In my experience, the hardest part of this simple task is putting the bulb back in and lining it up correctly. There are three tabs on the metal flange at the base of the bulb that must line up with slots in the housing. Pull the retaining clip out of the way and insert the bulb into the headlight cavity and align the tabs with the slots. Push the bulb in so that it is flush then push the retaining clip down and then toward the light bulb until it hooks under a hook on the bulb. If you've done this correctly, the retaining clip will be pressing the bulb firmly against the housing. Replace the cover by lining it up and turning it clockwise until it is tight. On the driver's side, line the cover up with the mating holes. Push the three plugs through the holes then screw the plastic screws in through the plugs the expand them until tight. Don't forget to replace the screw that attaches the cover to the bracket to the left of the battery.
I've made this sound a lot harder than it is. Sorry.

Jan 05, 2009 | 2005 Kia Spectra

1 Answer

Driver's side head light


There is 2 plastic clips behind the headlight, lift these up and pull the headlight out. Then just twist the plastic cap out of the headlight and replace. (Do not touch the bulb when replacing). Then put headlight back in all the way and slide the plastic retainer clips back into position.

Sep 23, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
Hyundai Motor 2003 Elantra Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...