Question about 2004 Jeep Wrangler

1 Answer

Fan motor When I turn my heat or ac on, it only work on high and no other setting. Does this mean I need to replace my fan motor? If so is it something I could do myself?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 507 Answers

Fan motor, no. It's more then likely your fan speed switch or the regluator. Sorry, 2004 jeeps are out of my league on where resistor is located.

Posted on Oct 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 isuzu rodeo AC/Heater blower making noise


Sounds like EXACTLY what you described (I've had that happen before). There is a leaf (or similar plastic/natural object) in your fan blower. This is located under the dashboard, typically under (or most easily accessed from) the passenger floorboard. If lucky and like mine, it was a few bolts (3 or 4) to take the cover off (with the blower attached), and all kinds of dirt, and a big leaf, fell out. They get in when the outer air vents are open. Good luck!

Dec 04, 2013 | 1999 Isuzu Rodeo

1 Answer

My mother in laws 2002 century blower only works on high..


It is not the blower motor.
On the 2002 model, I am showing an HVAC control module and a blower control processor. The control module handles the temp control and blower speed, and the processor contains the resistor for slower blower speeds.
Which component did you replace ?

Jun 30, 2013 | 2002 Buick Century

1 Answer

2003 explorer fan only works on high


I am assuming you mean the blower motor for the heat and ac.
There is a blower motor relay and a resistor in the circuit that would need to be tested.

Feb 26, 2013 | 2006 Ford Explorer

1 Answer

SW1 AC will only go on high or turn off, it won't turn on a lower setting. Help? what could it be?


What you mean is the blower motor will only run on high, right ?
It could be the fan switch or the resistor.

Jul 09, 2012 | Saturn Cars & Trucks

1 Answer

AC and Heater fan will only work on high speed, all fuses good. any ideas thanks, Dave


When the blower fan will only work on high speed setting this means the fans speed control resistor is burned out, when it fails the fan defaults to high speed only. The fan resistor is located next to the fan and held into the cooling air duct by 2 screws near the blower motor. The part is fairly cheap and easy to replace.

May 11, 2011 | 2000 Mercury Villager

1 Answer

Jump air compressor ac works replace relays same issue HONDA


the compressor may be low on freopn but, the fan problem is most likely the fan motor as it is the low temp fan and will run more often than both fans...to test see if you can switch the fan plugin to the other fan watch carefully that it does not get too hot as the second fan is a safety fan that works as high temp or when using the A\C

Jul 13, 2010 | 1997 Honda Accord

3 Answers

Subject: 2004 isuzu rodeo...my ac/heater blower is not working


The resistors are in circuit only on the lower fan speed settings.
On the highest speed setting, power is switched directly to the fan motor.
Check fan power supply fuses,
Check power is available to the fan when high speed selected.
If all above OK, apply power directly to the motor to verify fan motor runs- if it doesn't the motor may need replacement/repair.

Jul 29, 2009 | 2004 Isuzu Rodeo

3 Answers

1995 Subaru Impreza wagon - heater fan


Mine use to work on high only. It was the switch cylinders, something like that. It was an easy fix. Now my blower motor works intermittently. If I kick it, it turns back on. It is located on the passenger side close to the door side directly above your feet (below the jockey box). Kick straight up. If you need to replace it it is also an easy do-it-yourself repair. Make sure before you go out and replace your blower motor that you check your switch. A lot of repair shops will replace the motor w/o checking the switch, you end up paying for 2 repairs. You can make sure it's not the switch by jumping (bypassing) the switch.You apply jumper wires (not cables) directly to the motor, if the motor turns on you know it's the switch.

Jan 01, 2009 | 1995 Subaru Impreza

1 Answer

Ac & heater


Disconnect the wire from the fan, turn the car on, test the voltage between the connector to ground (chasis) on all fan speed settings (high,med,low). If you have voltage at all settings (approx. 12.3V on high and less as the speed setting is lower) then replace the fan motor (about $50 at autozone). If there is not voltage on all speed settings you will also need to replace the blower motor resistor (about $12 at autozone). The whole process takes about 20 mins.

Oct 09, 2008 | 1999 Oldsmobile 88

Not finding what you are looking for?
2004 Jeep Wrangler Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...