Question about 1999 Ford Crown Victoria

1 Answer

Having a problem resetting my keyless remote in my 1996 crown cic any idias

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

I would try taking the battery from the remote for a minute. Once you do that, put it back in, and seal the remote.

Step over to the car, stand in front of it, and hold the "Lock" and "Unlock" buttons for 15 seconds, or until the car honks the horn at you. It could be one short, several short, or any combination.

Some remotes also have the reset instructions on the inside of the back plate.

Posted on Jan 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I program the car to recognixe the key fob.


1996 Roadmaster

  1. Locate the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has black/white wires leading up to it and it is not connected to anything.)
  2. Jump programming connector terminals. Leave terminals jumped unitl step 6.
  3. System should now lock and unlock doors to indicate programming mode has been entered.
  4. Press any button on keyless remote once. System should now lock and unlock doors, indicating successful programming of keyless remote.
  5. Repeat step 4 for additional remote or other existing keyless remote. NOTE: A maximum of only two Keyless Remotes can be programmed.
  6. Remove programming connector jumper wire to exit programming mode.
  7. Test remote(s).

Oct 19, 2015 | 1996 Buick Roadmaster

1 Answer

Ho do i reset the key pad on my 98 ford crown vic??? help also its a p74 i was told it was an police car but not tactical more of an higher up when i called ford they told me the same thing....? is t


This is what I did on my 99 Grand Marquis. Maybe it will work for you.

1. Turn ignition from OFF to RUN 4 times within 3 seconds, with the 4th time ending in RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds, press any button on first keyless remote. Door locks will cycle to confirm programming.

3. Within 20 seconds press any button on second keyless remote. Door locks will cylcle to confirm programming.

4. Turn ignition to OFF.

Dec 13, 2014 | 1998 Ford Crown Victoria

1 Answer

We are having a problem with the computer under the radio saying hatch is open passenger side is open is their a way to reset it ?


you might have to reset keyless remote and or computer easy fix is on google type in search the make and model and
reset keyless remote and computer for doors very simple

May 22, 2014 | 1996 Jeep Cherokee

1 Answer

How do you program the transmitter on a 1996 Lincoln Town Car?


1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.

3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.

4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).

5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

Mar 28, 2013 | 1996 Lincoln Town Car

1 Answer

1996 jeep keyless remote receiver


on my cherokee its in the dome light housing google it
or google grand cherokee forums

Feb 02, 2013 | 1996 Jeep Grand Cherokee

1 Answer

Where is the keyless entry codw foe my 96 crown vic


That is located on the keyless entry module on a paper tag. The module is in the trunk, either behind the side panel or under the rear package tray drop down.

Feb 17, 2012 | 1996 Ford Crown Victoria

1 Answer

How do you prgram remote keyless entry


Here are the instructions from the factory service manual:
1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.

3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.

4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).

5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

Sep 14, 2011 | 1995 Ford Crown Victoria

1 Answer

My boyfriend bought a 1996 ford explorer, from a friend who is now passed away. Every now & then the alarm goes off but he does not have a remote for the alarm or the code for the keyless entry on the...


The security computer box is in the cargo area open the rear hatch on the driverside behind the plastic is the box, it will have the keyless entry code printed on the side.

Jan 18, 2011 | 1996 Ford Explorer

1 Answer

Keyless remotes won't work after battery change.


Remote has to be reprogramed. Look in owners for proceedure. If you don't have a manual call the dealer. May have to take vehicle to them to reprogram it with a scantool

Feb 19, 2010 | 1996 Toyota RAV4

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...