Question about 1994 Ford Mustang

1 Answer

Timing Replaced a pick up sensor and when timing is set and car then sets for a couple of hours car will not start unless we adjust timing again

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 95 Answers

Make sure its the right pick up then try resetting the distributer by one tooth advanced

Posted on Mar 20, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What else could cause a no start condition turns over ok occasionally it will fire

Fire when? as you release the key? If so replace the ignition switch. If you have fuel and spark it should start unless it is way out of time or the security is set. Another thing to consider is the spark plugs. Since you have had so much gas threw the engine, they may be fouled out.

Feb 05, 2015 | Cars & Trucks

1 Answer

My 95 Jeep Grand Cherokee keeps shutting off while driving. Sometimes I can put it in neutral and restart the engine while rolling. Most times, not. After 5-10 minuets and as many times cranking, it will...

54 - Sync Pick-Up Signal Not Detected (Camshaft Position Sensor/Ignition Pickup). recheck to see if power to sensor. make sure wire is in good shape, to cam sensor. 11 - No Crank Reference Signal At Power control module, crank shaft sensor. check to see if your getting signal from pcm. Good-day!

May 20, 2014 | Cars & Trucks

1 Answer

1988 22r pickup have to pump the gas now before starting 15 to 20 times. i didnt use to have to pump the gas before every start if it sits more than 10 hours it wont start unless i start pumping the gas...

Seems like the choke is not turning on. The 22r uses a carb if I'm not mistaken. pump it a couple of times then try pressing the pedal completely down before trying to start it. Then press the pedal half way down. the point is to set the choke when you press the pedal all the way down.

Oct 31, 2011 | 1988 Toyota Pickup

1 Answer

My 2002 Hyundai Accent has had a starting issue for the last month. It will crank but not start. My local mechanic has checked the crank and cam sensors (both fine), replaced the starter (which was old...

yes ---several
one is called an ambient temp sensor that reports to the ECM as to the fuel setting required ( acts like the old pull choke button)
next is a baro sensor that reports the density of the air --again to adjust fuel setting and lastly a mass air flow or mass air volume sensor that again reports to get the fuel setting right
if your local mechanic is not using a scanner tool to have the fault codes read before he picks up spanners , take it to an accredited service center with experience on your make of car and ask for a code reading before work being done
( auto zone does the readings for free)

Apr 03, 2017 | 2002 Hyundai Accent

1 Answer

Stalls occasionally but starts back up has left me set 3 times now drove some where parked was there for couple hours would not start went back a couple hours later and starts and run fine

This is usually the crank position sensor...some parts shops can help you with the location...hope this helps:) This should keep you from being stranded...

Dec 24, 2010 | 1994 Dodge Intrepid

1 Answer

Engine quit on the road had new engine put in still willnot start seems to be off time but assured timming is set correctly replaced ecm still no help please help

If it has a coil pack the timing is partially adjusted by the ECM using readings from other sensors such as the Cam position sensor and the crank position sensor but if the timing belt wasn't set correctly to begin with that won't be able to make the adjustments needed.

Jul 26, 2010 | 1996 Chevrolet Suburban

1 Answer

Yesterday in 90 degree weather after my car runs for a couple hour and gets hot it wants to shut down it makes a noise like it is not getting any power. After you let it set for about 20 minutes it allowed...

Lets start with the easy first and replace the fuel filter. One the fuel filter has been replaced and the problem persist, we can go to the next step and check the fuel pressure at the shredder valve. But for now it's most likely the fuel filter has come to the end if it's life, they should be replaced every 30,000 miles or once a year which ever comes first. Good luck and keep me posted. You can pick up the fuel filter st Auto Zone and they can give you the step by step instructions to getting the job done and Will also have the quick fuel line release wrench for lone or purchase. 

Jul 02, 2009 | 2000 Oldsmobile Bravada

1 Answer

Van Wont Start Then Start's

please explain what you are calling a crank cap?? is it the magnetic pick up sensor on the flywheel if so either clean the connections in the multiplug or try putting the old one back on

Apr 05, 2009 | 2001 Chrysler Voyager

1 Answer

2002 Saturn L200

There is a "crank sensor" that may need to be replaced - had the same problem with mine - it took the mechanics FOREVER to find out what was rrong

Jun 07, 2008 | 2002 Saturn L-Series

Not finding what you are looking for?
1994 Ford Mustang Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides