Question about 1996 Ford Probe

1 Answer

Spark plug removal

Can anyone tell me how to remove and replace the spark plugs on my 1996 ford probe.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to use an extention and a socket. I'm not sure what size socket.

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to locate the number 4 spark plug wire to replace the spark plug can you tell me how to locate this wire on a 05 ford expedition


Your vehicle doesn't have spark plug wires . Has coil on plug ignition system . Eight individual coils sitting right on top of the spark plugs . An the spark plugs have the tendency to break in the cylinder head . Does your ford have the 5.4 L 3 valve engine . Your best bet is to take your vehicle to a qualified repair shop that has the tool to take the broken spark plug out off the cylinder head. Ford 4 6L 5 4L 3V Spark Plug Removal Watch this ford tech .

Jun 29, 2016 | Ford Cars & Trucks

1 Answer

I have a 1990 ford 460 EFI cylinders 1,2,6 has no change or little in RPM when spark plug wires removed.The three spark plugs has black carbon on them. I replaced them with new ones with new wires.Co


check that the egr valve is not stuck open remove it and cover the hole on the intake side and see if it goes away or with engine running remove the vac line from the valve and install a short length of hose and suck on the hose to draw a vac on the valve it only takes 3-5 inches of vac to open it the engine should stall or run even worse if it is not stuck and if it was stuck open you didnt change anything

Dec 07, 2012 | Ford F 450 Super Duty Cars & Trucks

1 Answer

Where are the spark plugs in Ford KA 1999 and how do i change them


IF YOU HAVE THE EI IGNITION SYSTEM.YOUR SPARK PLUGS IS UNDER EACH INDIVIDUAL COIL.DISCONNECT COIL ELECTRICAL CONNECTOR.THEN REMOVE COIL RETAINING BOLT.THEN REMOVE OFF SPARK PLUG.THEN REPLACE SPARK PLUG.YOU HAVE 8 COILS TO REMOVE BEFORE REPLACING SPARK PLUGS.

Feb 16, 2011 | 1999 Ford Explorer

2 Answers

How do you replace the spark plugs on a 1998 2.7 Intrepid?


Hi,
REMOVAL
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • Prior to removing the spark plug, spray compressed air around the coil area and spark plug.
  • Remove electrical connector from ignition coil.
On 3.5L engines, it is necessary to loosen the screws by alternating back and forth. Do not lose the spacers under the coil when loosening the screws.
  • Remove 2 fasteners from ignition coil.
  • Remove ignition coil assembly.
  • Remove the spark plug using a quality socket with a rubber or foam insert.
  • Inspect the spark plug condition.
INSTALLATION
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • To avoid cross threading, start the spark plug into the cylinder head by hand.
  • 3.5L engines tighten spark plugs to 28 N·m (20 ft. lbs.) torque, 2.7L engine tighten spark plugs to 17.6 N·m (13 ft. lbs.).
  • Install ignition coil assembly onto spark plug.
  • Install coil screws and tighten: 2.7L engine to 6.2 N·m (55 in. lbs.), 3.5L engines to 6.7 N·m (60 in. lbs.).
  • Connect the electrical connector.

Aug 27, 2010 | 1996 Dodge Intrepid

1 Answer

How to replace spark plugs for 1999 ford contour


to replace spark plugs remove spark plug wire boots. use special sparkplug socket or else you can break the sparkplug. to remove turn ratchet counterclockwise remove all four one at a time, make sure that the sparkplug gap is correct. most plugs come pregapped...read the box it will tell.you. do not overtigheten plug once it has fully seated give it a good snug....if you do one at a time you dont need to mark the spark plug wires. if you mix up the wires your car will back fire which could cause severe internal damage.

Feb 13, 2010 | 1999 Ford Contour

1 Answer

Ford fiesta,1996,petrol,fails to start.


either your fuel pump relay or the safety shut off switch

Jul 02, 2009 | 1996 Ford Escort 4 Door

1 Answer

Spark Plug Wires -- 2000 Ford Focus ZX3?


two options just pull them straight up or they make a special tool that you can buy to do this. if you are going to replace plugs you should go ahead and do the wires at the same time.

Jun 20, 2009 | 2000 Ford Focus

1 Answer

Good Morning


What is a Taurus 2 cycle??? When does it misfire? Report fully!

Quick and simple solution is change the spark plugs, use the plain platinum type, and the spark plug wires. When installing the plugs, be sure to use antiseize compoud on the plug threads before installing them. The proper spark plug gap will be listed on a sticker label under the hood. It helps to remove them air filter assembly and duct work to get easier access to the back three plugs.

Sep 19, 2008 | 1996 Ford Taurus

1 Answer

96 probe


Pull the CPS Plug apart and clean that.
It's the grey one near the cambelt end and leads down to the crankshaft pully.

May 19, 2008 | 1996 Ford Probe

Not finding what you are looking for?
1996 Ford Probe Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...