Question about 1992 Geo Tracker

1 Answer

Timing for a 92 chevy geo tracker

My BF changed the timing belt and needs to know how to set the timing marks and which way the pully needs to go to set them ty

Posted by on

  • Anonymous Apr 07, 2009

    timing for 1995 geo tracker

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Point the pulleys to there timing marks and point the dist. to #3 postion......

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my timing belt running off pullies 95 geo tracker


we have that. covered,. all ways but sunday.
its not aligned, buy why , is it not.
1 page dedicated to drive.

http://www.fixkick.com/t-belt/drift.html

May 17, 2014 | 1996 Geo Tracker 2 Door

1 Answer

Need cam to crank diagram for 1997 geo tracker


my wild guess, timing belt change out?
or valve lash or , no matter it's all here.

this is the G16B engine,
this full timing belt page, is here. and has link to actual FSM page.
http://www.fixkick.com/t-belt/16-fast-belt-install.html


related issues here

http://www.fixkick.com/t-belt/tbelt-index.html

Apr 18, 2014 | 1997 Geo Tracker 2 Door

1 Answer

No just finished a valve replacement on 92 geo tracker 8v eng. set crank to TDC on #4 cyl and the cam to the proper alignment notch on rear valve cover and installed the new timing belt. However after all...


When timing belts are installed, the normal position of the crankshaft is for #1 cylinder to be at TDC. Here is a picture of the timing belt routing and the timing marks.

chuckster57_44.gif

Jun 04, 2011 | 1992 Geo Tracker

1 Answer

I need to know witch tining marks do i line up with the timing mark on a 95 tracker the I or E on the cam shaft


Click on the following free, direct Link. It has the Timing + Marks: Belt Diagrams, including for your 1995 Geo Tacker, 1.6L SOHC 4-Cylinder.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1995/make/geo/model/tracker/1995_geo_tracker_timing_belt_diagram_marks.htm

Apr 19, 2010 | 1995 Geo Tracker

2 Answers

Looking for timing belt diagram on 97 Geo Tracker


Click on the following free, direct Link. It has the Timing Belt Diagrams, including Marks and Instructional Diagrams.

Let me know if this helped...

http://www.2carpros.com/car_repair_information/year/1997/make/geo/model/tracker/1997_geo_tracker_timing_belt_diagram_marks.htm

Apr 08, 2010 | 1997 Geo Tracker 2 Door

1 Answer

Need to change timming belt 1997 geo tracker


TIMING BELT CHANGE You should have some mechanical skills before attempting any engine maintenance! These are basic instructions, and you must knoe what you removed, when, and what order so you can reinstall them in order. First, you have to remove everything in the way! You need to remove the Fan, clutch, and shroud, pump pully & drive belts. Next, you need to remove the Crank Pully:

1. Crank Pully Bolt 2. Crank Pully 3. Center Bolt 4. 5mm Hex drive (used to remove pully bolts) Once the fan stuff, and pully(s) are removed, then you need to remove the Timing Belt cover:

Once the cover is removed, you will need to loosen the adjusting nut and pully bolt on the Belt Tensioner:
A. Adjust Nut B. Pully Bolt C. TENSIONER PULLY Once the the Adjust Nut, and Pully bolt are loose, move the pully as far towards the water pump as possible.
Then, you can slip the timing belt from the sprockets. Check the tensioner for roughness and excess play! DO NOT MOVE THE CAM OR CRANK SPROCKETS! IF you do, then you will have to line up the Crank and Cam for piston number one at Top Dead Center before placing the new timing belt on! Note the timing marks on the crank and camshaft sprockets. IF YOU MUST! Allign the Cam and Crank at piston#1, Top Dead Center before removing the belt. Each sprocket has a small hole, with a line through it, and there is a small groove or "V" it alligns with on the engine. Now, once the timing belt is off, look at your new timing belt. Older belts use the Squared off teeth, while new ones have the rounded teeth. Make sure you have the correct belt for your sprockets! Never reinstall a belt that is in questionable condition. BELT WEAR CONDITIONS
If there are Arrows on the belt, they must be pointing to the RIGHT when you put the new belt on the sprockets. If there isn't one, then paint one on, and place the belt back on the sprockets. The arrow will indicate to a mechanic, this is the way the belt must be put back on (if they replace any cam or crank oil seals). Slip the new belt onto the Crank sprocket. While maintaining tension on the side of the belt opposite the tensioner, slip the belt onto the Camshaft sprocket. Releace the Tensioner adjusting nut to allow spring tension against the belt. Temporarily reinstall the crank pully, taking care to align the notch in the pully with the raised area on the sprocket. Rotate the crank clockwise two complete revolutions. Recheck the alignment of the of the valve timing marks. If they do not align properly, loosen the tensioner, slip the belt off the crank pully, align the timing marks, reinstall the belt, and check alignment again. Tighten the tensioner nut, then the bolt. Reinstall all parts removed, in the opposite order, of course. Start the engine and allow to reach normal operating temp, then road test. THEORETICALLY, you should simply be able to replace the belt with the new one, and go, as long as you did not move any of the sprockets when removing or installing the belt. Most people do it this way, and do not test for alignment before replacing everything. When the belt wears, timing will be off, very little, and this is why you check alignment. The belt may have slipped a tooth, making the timing off. This is why the Cam and Crank sprockets must both align properly. An experienced person will do just that: Replace the belt, and go. It really isn't all that hard. It helps to have a second person around with some experience also.

Nov 11, 2009 | 1997 Geo Tracker 2 Door

3 Answers

I need a diagram of engine timing marks for a 1.6 litre engine


1996 Geo Truck Tracker 2WD 1.6L MFI SOHC 4cyl

2efa731.jpg

Fig.: Before installing the timing belt, position the camshaft sprocket (1) so that the timing mark on the sprocket (2) is aligned with the notch (3) on the inside timing belt cover (4) ...

5a2ee07.jpg

Fig.: ...and ensure that the crankshaft sprocket (1) timing mark (2) is aligned with the mark on the oil pump (3)

For more details, can register in autozone.com (free).

I hope help you with this (remember rated this help) Good luck.

Oct 15, 2009 | 1996 Geo Tracker 2 Door

1 Answer

How to time a 1995 geo tracker


if u mean set the timing....u need the proper tools .....and specs ....and if you have changed timing belts or chains .....replacement procedure is very precise....;-)....but with proper timing light an specs setting timing is relatively easy........but in order to tell u i need to know what timing light ur using....

Sep 26, 2009 | 1995 Geo Tracker

2 Answers

Timeing belt for 92 geo metro 3 cyl


The timing marks are as follows
1. there is a "V" on the cylinder head cover.
2. Timing mark on camshaft timing belt gear
3. "Arrow mark" oil pump case
4. Punch mark on crankshaft gear.
DON'T MESS UP! THIS IS AN INTERFERENCE FIT ENGINE! IT WILL BEND VALVES!

Apr 06, 2009 | 1992 Geo Metro

Not finding what you are looking for?
1992 Geo Tracker Logo

793 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...