Question about 1995 Honda Accord

1 Answer

Honda accord trying to get to the water pump but cant undu the pully bolt (get to it through the passanger wheel ) ?????????help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 1,779 Answers

Unfortunately, u must remove the timing belt. This is why it is recommended to change the water pump when the timing belt is changed.
Here's the procedure : Disconnect neg. battery cable, remove splash shield at wheel well, (after removing wheel to help gain access, turn the engine to align timing marks and set #1 cylinder at top dead center on the COMPRESSION stroke. Once this is done, u can NOT disturb engine or u will have a fun time trying to figure out how the heck to set the timing. Drain anitfreeze, remove timing belt, remove water pump bolts (be aware that bolts may be different lengths, don't mix them up, remove water pump and O ring.
Put it back together: install new O ring and water pump, be careful Oring doesn't slip or move out of position, tighten to 9 ft lbs, install timing belt, refill antifreeze, reconnect battery cable, start car, check for leaks, bleed cooling system, replace splash shield.

Posted on Oct 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to locate and replace the water pump on 1997 nissan sentra.


The water pump is located on the passanger side of the engine. Look right below the timing chain cover and there is a pully and belt on the water pump. You will have to remove the water pump and thermostate together then seperate them after you get them off the car. I would recommend replacing the thermostate also (cheap fix). You will have to remove the belt and pully before you can remove the water pump. Hope this helps....

Jan 05, 2013 | 1997 Nissan Sentra

1 Answer

Whaere is the water pump located


The water pump is on the top right hand side of the engine if you standing on the passenger side looking at the front of the engine. Keep in mind that the water pump only goes back on one way, so make sure that you have it clocked right or the bolts wont line back up. Remove the water pump pully first before you take the belt off. This makes it easier to break the pully bolts loose and then remove the water pump bolts. Then after, put the pully back on and then the belt and then tighten the pully bolts, the belt will help hod the pully for you.


360dreamworx_44.gif
360dreamworx_45.gif
360dreamworx_46.gif

Aug 08, 2011 | 2003 Buick Rendezvous

3 Answers

I'am replacing water pump 2006 grand prix,all bolts are remove but one. I can't remove it because theres a wheel pully in the way. I think it's the power steering pump help.


You may have to remove the pump...
BUT , maybe not...
The pump pully has holes in it... with the power steering belt loose or off ... turn the pully to see if the holes will allign with the bolt you are trying to remove... if not... then the power steering pump must be removed to gain access to the last bolt..

Sep 26, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

Repair instructions for a leaking power steering pump on a 1997 honda accord. leaking from the shft bearing behind the pulley. need instructions to replace the oil seal.


Not a simple job unless you have proper tools. You'll need a gear puller to remove the pully and a compressiondevice to install the seal and retaining ring. Try a auto junk yard for a used pump. It'll be cheaper and a simple bolt on job.

Feb 22, 2010 | 1997 Honda Accord

1 Answer

WHERE IS THE WATER PUMP LOCATED...2003 ELANTRA


hi from uk fortunately the water pump on your car is not driven by cambelt ! the pump is driven by serp belt the pumps location is = if you look at front of engine view from front wing as you look down front you will see a large pully on left of cambelt covers and this is the water pump access to pump is best by supporting car and removing wheel and then the under wing cover that is secured by screws some advice for you if you intend renewing pump the pump pully is secured by 4 bolts use a 10 mm cranked ring spanner or socket loosen these bolts before you remove the drivebelt as belt holds pully and helps to prevent pully turning as you try to loosen these bolts hope this helps ?

Jan 26, 2010 | Hyundai Motor 2003 Elantra

1 Answer

O.k. I have the bottom bolt off for the alternator and the belt off the wheel but i cant get to the top pully what do i do to get the top pully off to get to the top bolt for the alternator


By the "top pulley" you would be referring to the water pump pulley? This is held on with 4, 10mm head bolts. Make sure you have disconnected the battery and then removed the battery cable from the back of the alternator before continuing.

Dec 27, 2009 | 2001 Suzuki Esteem

2 Answers

1999 Buick Park Avenue water pump removal


that is not an idler pully that is the power steering pully if you feel through the holes in the pully you will feel the 13 mm head bolts that hold the pump to the block remove those bolts the pump will drop down and you can then remove the water pump also you have to remove the studs using the inverted torx end on the stud to unscrew it then the mount will come out

May 10, 2009 | 1991 Buick Park Avenue

1 Answer

Remove and replace waterpump 1995 3.1 V6


3.1 V6's are not hard to do. If you stand infront of the car on the passanger side follow bottom radiator hose that is the water pump. There are 4 or 5 bolts holding the pully on do not take belt off yet. Break looses the bolt's first. Pull the pully off there will be at least 4 bolts holding the housing on remove them you will loose about a glass of water. Pull the old water pump out and put new one in make sure you use blue silicone or something similar for water put silicone on water pump make sure holes line up on the gasket when you put it on the pump let sit for 5 min. put silicone on other side of gasket put it right one don't let site reassemble everything and your good to go.

Jul 30, 2008 | Chevrolet Corsica Cars & Trucks

Not finding what you are looking for?
1995 Honda Accord Logo

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...