Question about 1996 Saab 900

1 Answer

Engine removal and replacement

I can't seem to fine any liticaure on removing and replacing 1996 900 se e
ngine

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 76 Answers

Dimitry Platonoff has graciously created a wonderful DIY site for Saabs.
Engine removal: http://photo.platonoff.com/Auto/20060518.Saab_NG900_Engine_Removal/
Engine reinstallation: http://photo.platonoff.com/Auto/20060710.Saab_NG900_Engine_Installation/
These tutorials are accompanied by many, many photos of the various steps of the procedures discussed. He goes by the handle "DIP" (his initials) and is a frequent poster on SaabCentral.com.

Posted on Oct 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Losing all power


no year, ?
is this 1nZ engine?
check all fuses yet.
did you connect a scan tool yet, and look?

Feb 19, 2014 | Toyota Yaris Cars & Trucks

1 Answer

My son has an automatic 2001 ford focus se.. It has bad vibrations under the gas pedal area and seems loud when driving.. The vibrations are there even when the car isn't moving.. The motor sounds...


Without seeing the car this can only be my best guess.

The exhaust runs out of the engine then between the engine and trans then right under the middle of the car, check your exhaust, look for missing or broken hangers.

The factory radio is ****, Ebay has many factory replacements, it seems the volume knob always fails first. To remove the unit go to your local Advance Auto or like and get the Ford radio removing kit, it's 2 bent wires O_o!

I do hope this helps.

Dec 31, 2010 | 2001 Ford Focus

1 Answer

Fog lights do not come on either when using headlights or with the fog lamp switch in my 2002 Grand Am SE. Fuse seems to be fine.


REPLACE THE FOG LAMP SWITCH DOWN ON THE STEERING COLM. REMOVE THE PROTEC. PANEL UNDER STEERING COLM. AND GENTLY START TO LOWER THE COLM. WATCH OUT FOR THE SHIFT IND. WIRE- REMOVE IT- LOWER COLM. AND HALF WAH DOWN ON THE TOP SIDE IS THE SWITCH FOR THE FOG LAMP CONTROL IF YOU HAVE ALREADY REPLACED THE ELEC. SWITCH - (PUSH BUTTON OR ROCKER STYLE ).IN THE DASH. IF - - LIGHTS AREON AND THE FOG LAMPS ARE TURNED ON AND THE HEAD LIGHT GO OUT OR WONT CHANGE FROM DIM TO BRIGHT REPLACE HIGH/LOW SWITCH ON COLM. SAME PROCEDURE AS FOG CONTOL SWITCH.

Nov 05, 2009 | Pontiac Grand Am Cars & Trucks

1 Answer

Good afternnon, I have a landrover 110 diesel 1987 the engine wont rev initially but if you hold down the accellerator it will slowly pick up.After engine has reached high revs when you remove your foot...


Its possible the fuel lift pump is faulty. remove the fuel filter, if you see that its half full of fuel, then this will tell you the pump is at fault.
There is a lever on the fuel lift pump, turn the ngine till you feel itgo harder, then feel the travel of the pump and if it is firm or easy to operate.
Lift pump failure is common on these.

Sep 21, 2009 | 1994 Land Rover Defender

2 Answers

I need to know the location of sensor 2 bank 2 on a 2001 maxima


this sensor would be in the right bank as you face the ngine from under the hood, it is the sensor before the catalytic converter in the exhaust pipe, u will need a 7/8" wrench or special O2 sensor socket to replace it, the tool type depends on how hard it is to remove, spray the threads with WD 40 before trying to remove. go to the link to see the oreintation of your engines cylinder banks, bank 2 has cylinder numbers 2, 4 ,6 in it.
http://autorepair.about.com/library/firing_orders/bl-fo-2618.htm

Aug 16, 2009 | Nissan Maxima Cars & Trucks

1 Answer

Ngine over fueling at all rpm, rough idle, heavy fuel consumption


if the car is stock i would replace your oxygen sensor. you may also need to clean out the MAF sensor.

May 29, 2009 | 1995 Volkswagen Golf

1 Answer

1997 dodge caravan p 1495 code


if I am not mistaken that is the code for the engine temp sensor, it kind of works as a choke, it tell the computer the ngine temp so it can lean out the fuel mix. I think the code says engine is taking too long to warm up. A faulty sensor will read -40 C all the time

Nov 07, 2008 | 1997 Dodge Caravan

2 Answers

Engine


it's look like the problem came from the injectors. they we're clogged. because hen the ngine still cool, it need much fuel than at working temperatures.

Jun 27, 2008 | 1995 Mercedes-Benz C-Class

Not finding what you are looking for?
1996 Saab 900 Logo

Related Topics:

624 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

rgbypoet

Level 2 Expert

162 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...