Question about Hyundai Motor 2003 Sonata

1 Answer

How do you remove front wheel bearings

Need to replace front wheel bearings need to know how they come out

Posted by on

  • phils74nova Oct 19, 2008

    thanks that is a big help i had looked at it and it looked big

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 53 Answers

This is a big job it requires a press. you must remove the knuckel assembely as a hole press out the hub remove a snap ring on the inner side of the knuckel then press the bearing out instalation in reverse i do not recomend trying this at home the going rate at most shops is 1.5 hours per side

Posted on Oct 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possible to remove and replace front wheel bearings with out a press


In order to remove the front wheel bearings without press hub off the bearing and then the bearing out of the knuckle. To do the first step need a a Support Bridge.It is a special tool. Make bridge and use a general bearing pulled kit to replace bearings. use a "Front Wheel Drive Bearing Removal Adapters Puller Pulley Tool Set Kit" .To replace the bearing, remove front CV shaft taking care not to move the CV shaft too far out .

Nov 06, 2015 | 2002 Kia Rio

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

Replace front wheel bearing


The front wheel bearing for your Impala is an integrated wheel hub/bearing/ABS.
The whole thing gets replaced. It should look like the one off my Bonneville; Bearing.

Remove wheel/tire. Remove brakes. Remove rotor. Remove axle nut. Press-out axle shaft*. Unplug ABS connector. Remove 3 bearing bolts.

*To press out axle, you may need a special tool from an auto parts store.
Don't forget to put the heat sheild back on during reassembly, and the axle nut need to be very tight.

zeevert_62.jpg


After Bearing/hub removed:
zeevert_73.jpg

Apr 21, 2011 | 2004 Chevrolet Impala

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

2 Answers

Does the front wheel bearing have to be machined


on that vehicle it,s replacement remove wheel remove brake caliper and pads remove brake caliper mount if you look on back side of spindle around area where axle comes thru you have three or four bolts remove bolts remove axle nut and hub bearing assembly comes off re-install in reverse order if this vehicle has 4 wheel abs unhook any wheel speed sensors

Mar 18, 2010 | 2003 Ford Explorer

2 Answers

Replacing front drive axle universal joints.


remove front wheel brakes,rotors, axle nut,remove the four bolts on the bake side of your unit bearing using one of the 4 bolts removed from the unit bearing (also knowin as wheel bearing) go get a half dozen of the same bolt only 1 to 2 inchs longer theard them into the unit bearing from the back side and start beating. the unit bearing is a sob to get out but will come out with time once you get it out pull out your axle shaft replace the ujoint and reassemble anti seize everything as you re assemble it

Jul 09, 2009 | 2004 Dodge Ram 2500

3 Answers

Right front bearings need lube


Hi if you are refering to the hub bearing it can not be lubed it is a sealed bearing it will have to be replaced

May 04, 2009 | 2002 Buick Park Avenue

1 Answer

How do I change Wheel Bearing


First I need to know if it is a front or rear bearing. If its a front, you could do the majority of the labor yourself and save some $$. You need to remove the steering knuckle that has the failed bearing. Once this is out, find a shop that will press the bearing and hub out and press the new bearing in. This is not something you can do yourself, unless you own and know how to operate a hydraulic press. Once the bearing has been changed out simply reinstall the steering knuckle, and take your car to get an alignment. If you have a rear bearing they are very easy. Remove the wheel and brake drum, then remove the 4 10mm bolts behind the knuckle to unbolt the bearing. Reinstalling is just the reverse of that.

Dec 13, 2008 | 1996 Saturn SL

3 Answers

Replacing front wheel bearing


those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Aug 28, 2008 | 2003 Mitsubishi Lancer

1 Answer

Replace front wheel bearings


The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Jun 20, 2008 | 1998 Nissan Sentra

Not finding what you are looking for?
Hyundai Motor 2003 Sonata Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...