Question about 2005 Chevrolet Avalanche

1 Answer

Window motor instalation

NO problem till the cables came alose and I cant see how to put them back. can you help, maybe a diagram?

Posted by on

  • ced1500 Jan 18, 2009

    the cable came off the little spool that the shaft of the motor turns I wound the cable back around the spool but it will not work right when I go up or down with the window

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Show how to put cable on rear window motor


You don't resting the cable you replace the window regulator. That siad there are no diagrams.

Jul 12, 2012 | 2001 Oldsmobile Aurora

1 Answer

Need cable diagram for lincolc town car 2003 tc drivers window cable has come off need diagram to show where the cable end ties on


If the cables for the window have come u done than the regulator will need to be replaced. You can not just put the cables back and get the window to work. The regulators are pretty common and are typically available at your local parts store. I assume you have the door panel off to see that the cables are not in the right place anymore. Another six bolts and the regulator will come right out. Swap the motor, reinstall and your good as new. If you need additional info or have more questions let me know and i'll be happy to help.

Oct 02, 2011 | Cars & Trucks

1 Answer

My mother just passed away and i inherited her 1991 S10 Blazer it only has 60000 miles on it and is in great condition, But the front windows do not go up or down. The back windows work fine. what should i...


GOD BLESS your mom...On back of fuse door there may be a diagram otherwise pull each fuse & check if good .. then go to door pull out swich & work your way back w/ vom till you have power ,,

Apr 21, 2011 | 1991 Chevrolet S-10 Blazer

1 Answer

Need a diagram of a 2001 GMC Yukon door, power window motor needs to be replaced


The diagram is kind of small, but here is some info.

Removal Procedure:
  1. Raise the window. If the window motor is inoperable, remove the window to gain access to the window motor retaining screws. .
  2. Remove the door trim panel. .
  3. Remove the water deflector.
  4. Remove the door speaker.
  5. Support the window.
  6. Disconnect the wiring harness from the window regulator motor
spacer.gif 767040.gif spacer.gif spacer.gif View Full Image spacer.gif

767040.gif

  • Remove the 3 bolts from the window motor located on the front side of the motor. Important: Do not allow the cable gear come out of the housing. A failure will result with the cable coming off the spool.
  • Separate the motor from the cable housing by wiggling the window motor. Observe the orientation of the window motor.
  • Remove the motor from the window regulator assembly Installation Procedure:
  • Install the motor to the cable housing by wiggling motor into place. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  • Install the 3 bolts to the window motor. Tighten
    Tighten the bolts to 5 N·m (44 lb in).
  • Install the window, if removed. .
  • Connect the wiring harness to the window regulator motor.
  • Remove the window support.
  • Connect the wire connector to the switch to inspect the operation of the window.
  • Install the speaker.
  • Install the water deflector.
  • Install the door trim panel.
  • Hope this helps. Good Luck!!

    Apr 06, 2010 | 2001 GMC Yukon

    2 Answers

    Left rear window won't go up unless i push it up. 1994 lincoln towncar. motor works. need diagram of inside door to see where it is getting stuck.


    Your window is not getting stuck. The plastic gear parts in the window motor has crumbled OR the cable in the window regulator has broken.

    Aug 10, 2009 | 1994 Lincoln Town Car

    1 Answer

    Window wont roll up


    Hi my name is Allen!

    When the window falls down it is because the cable for the regulator and motor broke. The only fix is a new regulator/motor assembly from the dealership, or a good one from the junk yard if you can find one.

    For further asistance you may reach me at FixYa!

    Dec 25, 2008 | 2001 Dodge Dakota

    2 Answers

    Driver's side window stuck open.


    unfortuanately the window has come off the track... happens for various reasons... on my windstar the side rail spot weld broke so the rail/track came off... i had to take the bracket out ... drill out the spot weld and put it back together with a rivet ... put the window back and it's been good since.... basically you will need to take the door panel off to see why it came off the track.

    Robert

    Dec 17, 2008 | 1999 Jeep Grand Cherokee

    1 Answer

    Window motor


    I can Scan the Diagram out of a shop manual if you would like?

    E-mail Me at worik_brown@yahoo.com

    Nov 24, 2008 | 1992 Isuzu Trooper

    Not finding what you are looking for?
    2005 Chevrolet Avalanche Logo

    Related Topics:

    154 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...