Question about Chrysler Voyager

1 Answer

We replaced the battery & now a code is required for the radio?

When radio is switched on it says "code" We don't have a code or a manual.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

If you take the radio out and bring it to a chrysler dealer there is a code on the side of the radio and the dealer can get your security code from this code.

Posted on Oct 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turned radio off then battery died, got vehicle fixed but no power to factory radio, all fuses check as good. Is there a trick to getting the radio to turn on again?


when the battery dies or is removed , the anti-theft code of the radio kicks in and the unit will not work again until a special code for that radio is reinstalled
the code could be in the user manual in the radio use section ,or there are sites on the net that may have the code for you

Mar 24, 2016 | 1998 Ford Expedition

2 Answers

Had to replace battery now radio is asking for code


The correct radio SERIAL NUMBER is required for a code

First remove the radio from the dashboard.

Removal Info here

www.fitaudio.com

Then post the radio make+model plus all the letters+numbers on any labels,barcodes and a 14 character Serial Number stamped in the metal casing.

This information can then be used to see if a code can be calculated


Radio Code advice always available here (including BMW Z3 radios )

www.ukbookshelf.co.uk

Oct 19, 2015 | 2001 BMW Z3

1 Answer

Radio code: could you help me how can i reset my toyota camry 2004 radio code?


look in the owners manueal there is a tag about 1/4 tall by 2" long or a creadt card that will have your radeo code. if not you have to call toyoata i think they need your vin number to get the code

Nov 27, 2013 | 2004 Toyota Camry

1 Answer

I just change the battery but I don't have the code radio for my BMW 323is


Your security code is in the BMW owners manual.
If you do not have the manual then you need to go to the BMW service centre to get this code.

Dec 20, 2011 | 1999 BMW 323 Series

2 Answers

My local dealer says my battery in my 2001 Chevrolet Suburban continues to drain because of a draw on the battery. It was determined that the amplifier was not shutting off when vehicle was turned off. ...


Hi Bob, Joe got in first, because that would have been my advise exactly! Find the power feed to the amp and then do what Joe advised. (Of course the choice of where you fit the switch is yours, you don't have to have it by your seat but it makes sense if you're driving alone) Regards John

Nov 10, 2011 | 2001 Chevrolet Suburban

1 Answer

Please after changing the battery of my VOLVO v40 1999 wagon car the radio requested code can you help me


This is a anti-theft device built into your radio designed to foil robbers. When the radio looses power, the radio locks up. This makes the radio worthless on the black market. The thieves know this and don't steal it as a result. Your owners manual tells you to clear the code if there will be a power loss (changing the battery). There may not be a recovery procedure.

In the GM (1995) version of this system, there is no recovery (if there were, what would be the point of the system?). I don't know the specifics of the Volvo system. You may want to talk to your dealer before you replace your radio. I am sure you will have to prove ownership of the vehicle.

Thanks for your question @ FixYa.com this morning.

Jun 21, 2011 | 2000 Volvo V40

1 Answer

Need radio codes i have the radio pulled out


Most of the time the dealer will provide you with the radio codes and write them in your owner's manual. If you don't have them - you will have to get them from the dealer. They most likely will require you to provide proof of ownership.

May 27, 2011 | 2000 Daewoo Leganza

2 Answers

My battery went dead on my ford fusion 2008 now my radio doesn't work


As with many newr cars, Your radio probably had a security code which is required to reset it after the radio is removed or power was disconnected from it. You probably have the code written somewhere in your new car paperwork. If not, contact your dealer. They can probably guide you through resetting the code.

Nov 03, 2010 | 2006 Ford Fusion

1 Answer

How don I reset the radio after the battery have been replaced thank you G.T


You have a factory stock code inside your owners manual(if you have the owners guide) that has the code to type into the radio to engage your stations and sound again.If you cannot locate the code card in your manual you will unfortunately have to physically remove the radio from the dash and write down the number off the side of the stock radio and call it in to the dealer and they can access your unlock code for ya..I hope I could help!!! Thanks for choosing us!

Apr 14, 2010 | 2004 Hyundai Elantra

1 Answer

After installing a new battery, the radio does not work


hello,for your radio,you need a radio code,if you don"t have ask your dealer to provide the code,alarm system is always activated when you lock the vehicle,ty

Apr 18, 2009 | 1997 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...