Question about 1997 Chevrolet Corvette

2 Answers

Harmonic balancer What are the steps to replacing a harmonic balancer on a 1997corvette

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What are the steps to removing a harmonic balancers

Posted on May 08, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,039 Answers

Remove the hood, drain and remove the radiator, remove the belts, loosen the bolt into the balancer, replace part way, hook up a harmonic balance puller, tighten until balancer come free, remove puller, remove HB bolt, remove balancer.
Check seals before replacing, if damaged, replace, check keyway, replace woodruff key if needed.
Install is the reverse.

Posted on Oct 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoe do I replace the harmonic balancer seal


you have to take your belts off first then if you have room you will need to take the harmonic bolt out then you will need a harmonic balancer puller once you get the harmonic balancer off the seal is on the crankshaft you will need to get the old seal out use a seal puller and installer to put the new seal in Oreilly auto parts lends these tools if you don't want to buy one,

Jan 18, 2015 | Cars & Trucks

1 Answer

How do I change a harmonic balancer on a 1999 f150. 4.2l engine


this is a bigger job to deal with: first step whatever is blocking the front of engine remove it because you need a harmonic balancer puller to remove it. In some cases you might have to remove the radiator to get more room. Remove belts, mounting brackets on other accessories, whatever is attach to it. make sure you replace the front engine seal before reinstalling the new balancer. good luck.

Nov 16, 2013 | Cars & Trucks

1 Answer

Harmonic balancer


remove center bolts and with puller remove the harmonic balancer.then after,to replace install harmonic balancer and the center big bolt with air gun tight it until it sit

Aug 07, 2013 | Oldsmobile Delta 88 Cars & Trucks

2 Answers

Had my Harmonic Balancer replace now it shuts off after 10 mins of it being on


the garage may have did something to the crank position sensor that is located behind the harmonic balance. there is a ring gear there to for the timing

Oct 30, 2012 | 2001 Pontiac Grand Prix

1 Answer

How much torque required on 2005 Buick Renzvous harmonic balancer?


3.4L V6 harmonic balancer bolt

step 1 52 ft lbs.

step 2 additional 72 degrees

3.6L V6

step 1 74 ft lbs.

step 2 additional 150 degrees

May 21, 2011 | 2005 Buick Rendezvous

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

1 Answer

Harmonic balancer bad car runs real bad


The harmonic balancer controls the triggering of the combined crankshaft/camshaft sensor. This controls ignition plus fuel injection. Replace the balancer and adjust the sensor or replace it if damaged.

Oct 18, 2009 | 1998 Pontiac Bonneville

1 Answer

I need a how to to change harmonic balancer for 1995 nissan maxima. step by step


First remove right front tire and support vehicle with a jack stand. Remove splash guard lower portion near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tenioner and then loosen the tensioner bolt (it is the one that stands out, you use a socket on it.). The power steering adjuster bolt with be gained from the bottom. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Pull down on the belt the help move it after you've loosened it some.Then remove harmonic balancer bolt (19mm).If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller onto the harmonic balancer (one finger on each side securely press into the belt groove. The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.

Aug 26, 2009 | Nissan Maxima Cars & Trucks

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

1 Answer

Harmonic balancer on a grand am


you have to remove the center bolt of harmony its depend what engine you have most likely you need a little puller if the belt loose check the belt tensionner to see if its not broken pierre

Feb 11, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1997 Chevrolet Corvette Logo

Related Topics:

932 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...