Question about 2000 Lincoln LS

3 Answers

Hydrolic pump for engine coolant fan

I had to take off my hydrolic motor to my engine cooling fan to replace the pulley,when i took hose off pump,aplunger and spring fell out ,i need a diagram to reinstall these parts,i put it back togather but fan does not kick on

Posted by on

  • 1 more comment 
  • jnormanhunte Oct 18, 2008

    i need diagram on which way the spring and plunger goes back in pump where hydrolic hose attaches

  • jnormanhunte Oct 18, 2008

    my 2000 lincoln ls has a seperate pump for power steering,the hydrolic fan pump is located on r/s frt of engine what i need to know is,when you take the hose loose from pump there is a spring and plunger inside the pump,which way do they go back in ,my car is a 2000 linc ls with a 3.0 v/6 engine

  • jnormanhunte Oct 19, 2008

    do you know how to repair this problem or not,if not don not charge to my credit card

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

Is this your pump?hydrolic pump for engine coolant fan - 1016d12.jpg

Posted on Oct 18, 2008

  • paul erickson
    paul erickson Oct 18, 2008

    or is this your pump the answer is different on which pump you have

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 306 Answers
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 19,396 Answers

Here is some instruction oin how to take apart and re-assemble the pump, Lincoln/Mercury Repair: lincoln ls cooling,if you need pictures you will have to buy the Haynes/ Chilton manual.

Posted on Oct 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace water pump


Removal & Installation

  1. Disconnect the negative battery cable.
  2. Drain the engine cooling system.
  3. For 5.3L engines, loosen the air cleaner outlet duct clamps at the throttle body and Mass Airflow/Intake Air Temperature (MAP/IAT) sensor. Remove the bolt and air cleaner outlet duct.
  4. Relieve the belt tension and remove the accessory drive belts or the serpentine drive belt, as applicable.
  5. Remove or disconnect the following:

NOTE
For the hoses on some engines, removal may be easier if the hose is left attached until the pump is free from the block. Once the pump is removed from the engine, the pump may be pulled (giving a better grip and greater leverage) from the tight hose connection.W

WARNING
Note the positions of all retainers as some engines will utilize different length fasteners in different locations and/or bolts and studs in different locations.

  • Upper fan shroud
  • Fan or fan and clutch assembly, as applicable
  • Water pump pulley; use a suitable tool to hold the pulley while removing the bolts
  • Coolant hose(s) from the water pump
  • Water pump retainers
  • Water pump from the engine



4.2L Pump Location26010723-pqcu5dneux0l02jg41pvmzkd-2-0.gif
5.3L Pump Location


26010723-pqcu5dneux0l02jg41pvmzkd-2-1.gif
To install:
  1. Clean the gasket mounting surfaces.

    NOTE

    The water pumps on some of the engines covered may have been installed using sealer only, no gasket, at the factory. If a gasket is supplied with the replacement part, it should be used. Otherwise, a 1 / 8 in. (3mm) bead of RTV sealer should be used around the sealing surface of the pump.
  2. Apply sealant to the water pump retainer threads.
  3. Install or connect the following:

    • Water pump using a new gasket. Tighten the water pump retainers to 89 inch lbs. (10 Nm) for 4.2L engines, or to 30 ft. lbs. (41 Nm) for 4.3L engines. For 5.3L engines, tighten the bolts to 11 ft. lbs. (15 Nm), then to 22 ft. lbs. (30 Nm).
    • Coolant hose(s)
    • Water pump pulley. Tighten the pulley bolts to 18 ft. lbs. (25 Nm).
    • Fan or fan and clutch assembly
    • Serpentine drive belt (if equipped) by positioning the belt over the pulleys and carefully allow the tensioner back into contact with the belt.
    • V-belts (if equipped) and adjust the tension
    • Upper fan shroud
    • Negative battery cable
  4. Refill the engine cooling system.
  5. Run the engine and check for leaks.

Dec 16, 2015 | 2004 Chevrolet TrailBlazer

1 Answer

How to change water pump on a 2009 Ford Fusion


2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Loosen the 3 coolant pump pulley bolts.
  4. Remove the accessory drive belt.
  5. Remove the 3 bolts and the coolant pump pulley.
    1. To install, tighten to 15 ft. lbs. (20 Nm).
  6. Remove the 3 bolts and the coolant pump.
  7. Remove and discard the O-ring seal.
    1. To install, tighten to 89 inch lbs. (10 Nm).


25940856-ldxojubx5kaly1k2zv3zks4n-2-0.gif Fig. Exploded view of the water pump-2.3L engine


To install:
  1. To install, reverse the removal procedure.
  2. Lubricate the O-ring seal with clean engine coolant.
  3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the coolant pump belt.
  4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.


25940856-ldxojubx5kaly1k2zv3zks4n-2-1.gif Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.


25940856-ldxojubx5kaly1k2zv3zks4n-2-3.gif
Fig. View of the water pump and related components-3.0L engine

To install:
  1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
  2. Position the coolant pump assembly and install the 3 bolts:
    1. Tighten to 89 inch lbs. (10 Nm).
    2. Tighten the 3 bolts an additional 90 degrees.
  3. Connect the coolant pump-to-engine hose and the heater hose.
    NOTE
    Install the coolant pump drive pulley flush with the end of the camshaft.
  4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.



25940856-ldxojubx5kaly1k2zv3zks4n-2-6.gif Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

Nov 04, 2015 | 2009 Ford Fusion SE

3 Answers

How to Install Waterpump


Water Pump REMOVAL & INSTALLATION 2.3L and 2.5L Engines Fig. 1: Exploded view of the water pump and related parts for the 2.3L and 2.5L engine 85553140.gif
  1. Disconnect the negative battery cable.
  2. Drain the cooling system. CAUTION
    When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  3. Remove the two bolts that retain the fan shroud and position the shroud back over the fan.
  4. Remove the four bolts that retain the cooling fan. Remove the fan and shroud.
  5. Loosen and remove the accessory drive belt. Earlier models may have two drive belts, remove them both.
  6. Remove the water pump pulley and, if necessary, the vent hose to the emissions canister.
  7. Remove the heater hose at the water pump.
  8. Remove the timing belt cover. Remove the lower radiator hose from the water pump.
  9. Remove the water pump mounting bolts and the water pump. Clean all gasket mounting surfaces.
  10. Install the water pump in the reverse order of removal. Coat the threads of the mounting bolts with sealer before installation.
2.9L Engines
  1. Drain the coolant from the radiator and remove the lower hose and the return hose from the water inlet housing. CAUTION
    When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  2. Using Tools T83T-6312-A and B remove the fan and clutch assembly from the front of the water pump. NOTE: See the engine fan removal procedure in this section.
  3. Loosen the alternator mounting bolts and remove the alternator belt.
  4. Remove the water pump pulley.
  5. Remove the bolts retaining the water pump assembly and remove the water pump, water inlet housing, and the thermostat from the front cover.
  6. Before installing the water pump, clean the gasket surfaces on the front cover and on the water pump assembly. Apply gasket sealer to both sides of the new gasket and install the water pump in the reverse order of removal.
3.0L Engine
  1. Disconnect the battery ground cable.
  2. Drain the cooling system. CAUTION
    When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  3. Remove the engine fan.
  4. Loosen the 4 water pump pulley bolts.
  5. Remove the accessory drive belts. Fig. 2: Exploded view of the 3.0L engine water pump 85553151.gif

  6. Remove the water pump pulley.
  7. Remove the alternator adjusting arm and throttle body brace.
  8. Remove the lower radiator hose.
  9. Disconnect the heater hose at the pump.
  10. Rotate the belt adjuster out of the way.
  11. Remove the water pump attaching bolts. Note their location for installation.
  12. Remove the pump and discard the gasket.
  13. Thoroughly clean the pump and engine mating surfaces. To install:
  14. Using an adhesive type sealer, position a new gasket on the timing cover.
  15. Position the water pump and start the bolts. When all the bolts are started, torque them to specifications. Refer to the necessary illustration. Fig. 3: 3.0L engine water pump and front cover fastener chart 85553152.gif

  16. Install the lower hose and connect the radiator hose.
  17. Install the pulley and hand-tighten the 4 bolts.
  18. Install the alternator adjusting arm and brace.
  19. Install the belts and tension them. See Section 1.
  20. Tighten the 4 pulley bolts to 19 ft. lbs.
  21. Install the fan.
  22. Fill and bleed the cooling system.
  23. Connect the battery ground cable. Run the engine and check for leaks.

Jan 13, 2011 | 1991 Ford Explorer

1 Answer

Replacing water pump


This is for the 3.9 v6 you did not specify motor size.
Hope this helps, it it does please leave feedback Thank You and Good Luck


The water pump can be removed and installed without discharging the air conditioning system (if equipped).
  1. Disconnect battery negative cable.
  2. Drain cooling system.
  3. Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094). SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.


  1. Remove upper radiator hose clamp and hose at radiator.
Fan Blade And Viscous Fan Drive-3.9L/5.2L/5.9L Engines 81898572


  1. The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. A Snap-On 36 MM Fan Wrench (number SP346 from Snap-On Cummins Diesel Tool Set number 2017DSP) can be used. Place a bar or screwdriver between water pump pulley bolts to prevent pulley from rotating. Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
  2. If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
  3. Remove fan shroud attaching hardware (two bolts at bottom-two clips at top).
  4. Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
  5. After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
  6. Do not remove water pump pulley bolts at this time.
Automatic Belt Tensioner Assembly-3.9L/5.2L/5.9L Engines 81898573


  1. Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front). When all belt tension has been relaxed, remove accessory drive belt.
  2. Remove four water pump pulley-to-water pump hub bolts and remove pulley from vehicle.
  3. Remove lower radiator hose clamp and remove lower hose at water pump.
  4. Remove heater hose clamp and heater hose from heater hose coolant return tube.
Coolant Return Tube-3.9L/5.2L/5.9L Engines-Typical 81898574


  1. Loosen heater hose coolant return tube mounting bolt and remove tube from water pump. Discard the old tube O-ring.
Water Pump Bolts-3.9L/5.2L/5.9L Engines 81898575


  1. Remove seven water pump mounting bolts.
  2. Loosen clamp at water pump end of bypass hose. Slip bypass hose from water pump while removing pump from vehicle. Discard old gasket.
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.


Belt Routing-3.9L/5.2L/5.9L Engines 81898576

Jan 01, 2011 | 1999 Dodge Durango

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

1 Answer

How to replace a fuel pump on a 1994 jeep grand cherokee?


I'm assuming that your Jeep have a 5.2L V8 engine (as mine), then check this procedure...

Grand Cherokee 5.2L Engines
(see Figure 6)
  1. Disconnect the negative battery cable.
  2. Open the radiator valve and drain the cooling system.
  3. Remove the cooling fan and shroud as an assembly.
  4. Remove the accessory drive belt.
  5. Remove the water pump pulley from the hub.
  6. Disconnect the hoses from the water pump.
  7. Loosen the heater hose coolant return tube mounting bolt and nut and remove the tube. Discard the O-ring.
25b04d0.jpg

Fig. 6: Water pump mounting bolt locations
  1. Remove the water pump mounting bolts.
  2. Loosen the clamp at the water pump end of the bypass hose. Slip the bypass hose from the water pump while removing the pump from the engine. Discard the gasket.
To install:
  1. Clean all gasket mating surfaces.
  2. Guide the water pump and new gasket into position while connecting the bypass hose to the pump. Tighten the water pump bolts to 30 ft. lbs. (40 Nm).
  3. Install the bypass hose clamp.
  4. Spin the water pump to ensure the pump impeller does not rub against the timing chain cover.
  5. Coat a new O-ring with coolant and install it to the heater hose coolant return tube.
  6. Install the coolant return tube to the engine. Ensure the slot in the tube bracket is bottomed to the mounting bolt. This will properly position the return tube.
  7. Connect the radiator hose to the water pump.
  8. Connect the heater hose and clamp to the return tube.
  9. Install the water pump pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  10. Install the accessory drive belt.
  11. Install the cooling fan and shroud.
  12. Fill the cooling system.
  13. Connect the negative battery cable.
  14. Start the engine and check for leaks.

Other details can find in your repair manual ZJ-Secc-7-Cooling-System

Hope thats help.

May 04, 2010 | 1994 Jeep Grand Cherokee

2 Answers

Where can I get solid/detailed instructions for changing out the water pump on my 2001 Yukon SLE 4.8? Something that would include torque specs. and any must does and don'ts would be nice.


Escalade, Suburban, Tahoe, Yukon, Denali, DenaliXL, YukonXL 1999-2005 Water Pump - Removal & Installation 4.8L, 5.3L & 6.0L Engines
  1. Remove or disconnect the following:
    Air outlet duct Coolant Inlet radiator hose from the water pump Upper fan shroud Cooling fan and clutch assembly Drive belt Radiator outlet hose from the coolant pump Surge tank hose Heater hose Water pump

    62c3d00.jpg
    Fig. Exploded view of the water pump assembly-4.8L, 5.3L and 6.0L engines
To install:

NOTE DO NOT use cooling system seal tabs (or similar compounds) unless otherwise instructed. The use of cooling system seal tabs (or similar compounds) may restrict coolant flow through the passages of the cooling system or the engine components. Restricted coolant flow may cause engine overheating and/or damage to the cooling system or the engine components/assembly.
  1. Install or connect the following:
    Water pump. Install the water pump bolts. Tighten the water pump bolts first pass to 11 ft. lbs. (15 Nm); tighten the bolts final pass to 22 ft. lbs. (30 Nm). Water pump drive belt pulley and bolts (if applicable). Tighten the pulley bolts first pass to 89 inch lbs. (10 Nm); tighten the bolts final pass to 18 ft. lbs. (25 Nm). Surge tank hose Heater hose Outlet radiator hose to the coolant pump Drive belt Cooling fan and clutch assembly Upper fan shroud Inlet radiator hose to the water pump Air inlet duct Coolant

  1. Remove or disconnect the following:
    Air inlet and outlet duct Coolant Inlet radiator hose from the water pump Upper fan shroud Cooling fan and clutch assembly Drive belt Radiator outlet hose from the coolant pump Surge tank hose Heater hose Water pump

To install:
  1. Install or connect the following:
    Water pump. Install the water pump bolts. Tighten the bolts to 11 ft. lbs. (15 Nm) for the first pass; then tighten to 22 ft. lbs. (30 Nm) for the final pass. Water pump drive belt pulley and bolts (if applicable). Tighten the bolts to 89 inch lbs. (10 Nm) for the first pass; then tighten to 18 ft. lbs. (25 Nm) for the final pass. Surge tank hose Heater hose Outlet radiator hose to the coolant pump Drive belt Cooling fan and clutch assembly Upper fan shroud Inlet radiator hose to the water pump Air inlet and outlet duct Coolant

Hope this help to solve it (remember comment and rated this).

Apr 26, 2010 | 2001 GMC Yukon

1 Answer

2006 dodge dakota water pump replacement instructions 3.7L


The water pump can be removed and installed without discharging the air conditioning system (if equipped).

  1. Disconnect battery negative cable.
  2. Drain cooling system. Refer to Draining and Filling found under Cooling System, Service and Repair.
  3. Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse. WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094). SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS. CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.
  4. Remove upper radiator hose clamp and hose at radiator.
  5. The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. A Snap-On 36 MM Fan Wrench (number SP346 from Snap-On Cummins Diesel Tool Set number 2017DSP) can be used. Place a bar or screwdriver between water pump pulley bolts to prevent pulley from rotating. Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
  6. 6. If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
  7. Remove fan shroud attaching hardware (two bolts at bottom-two clips at top).
  8. Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
  9. After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
  10. Do not remove water pump pulley bolts at this time.
  11. Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front). When all belt tension has been relaxed, remove accessory drive belt.
  12. 12. Remove four water pump pulley-to-water pump hub bolts and remove pulley from vehicle.
  13. Remove lower radiator hose clamp and remove lower hose at water pump.
  14. Remove heater hose clamp and heater hose from heater hose coolant return tube.
  15. Loosen heater hose coolant return tube mounting bolt and remove tube from water pump. Discard the old tube O-ring.
  16. Remove seven water pump mounting bolts.
  17. Loosen clamp at water pump end of bypass hose. Slip bypass hose from water pump while removing pump from vehicle. Discard old gasket. CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

INSTALLATION

  1. Clean gasket mating surfaces.
  2. Using a new gasket, install water pump to engine as follows: Guide water pump nipple into bypass hose as pump is being installed. Install water pump bolts. Tighten water pump mounting bolts to 40 Nm (30 ft. lbs.) torque.
  3. Position bypass hose clamp to bypass hose.
  4. Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
  5. Install a new O-ring to the heater hose coolant return tube. Coat the new O-ring with antifreeze before installation.
  6. Install coolant return tube and its mounting bolt to engine. Be sure the slot in tube bracket is bottomed to mounting bolt. This will properly position return tube.
  7. Connect radiator lower hose to water pump.
  8. Connect heater hose and hose clamp to coolant return tube.
  9. Install water pump pulley. Tighten bolts to 27 Nm (20 ft. lbs.) torque. Place a bar or screwdriver between water pump pulley bolts to prevent pulley from rotating.
  10. Relax tension from belt tensioner. Install accessory drive belt.
  11. CAUTION: When installing the serpentine accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Illustration above for correct belt routing. The correct belt with correct length must be used.
  12. Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
  13. Install fan shroud.
  14. Install fan blade/viscous fan drive assembly to water pump shaft.
  15. Fill cooling system.
  16. Connect battery negative cable.
  17. Start and warm the engine. Check for leaks.

Feb 28, 2010 | 2006 Dodge Dakota

1 Answer

Replacement of water pump on 2004 gmc sierra 2500hd 6.0l. any tips on removal and installation


Remove or disconnect the following:

Air outlet duct Coolant Inlet radiator hose from the water pump Upper fan shroud Cooling fan and clutch assembly Drive belt Radiator outlet hose from the coolant pump Surge tank hose Heater hose Water pump

0996b43f802030d1.jpg

DO NOT use cooling system seal tabs (or similar compounds) unless otherwise instructed. The use of cooling system seal tabs (or similar compounds) may restrict coolant flow through the passages of the cooling system or the engine components. Restricted coolant flow may cause engine overheating and/or damage to the cooling system or the engine components/assembly.

Install or connect the following:

Water pump. Install the water pump bolts. Tighten the water pump bolts first pass to 11 ft. lbs. (15 Nm); tighten the bolts final pass to 22 ft. lbs. (30 Nm). Water pump drive belt pulley and bolts (if applicable). Tighten the pulley bolts first pass to 89 inch lbs. (10 Nm); tighten the bolts final pass to 18 ft. lbs. (25 Nm). Surge tank hose Heater hose Outlet radiator hose to the coolant pump Drive belt Cooling fan and clutch assembly Upper fan shroud Inlet radiator hose to the water pump Air inlet duct Coolant

Jan 15, 2010 | GMC Sierra 2500HD Cars & Trucks

Not finding what you are looking for?
2000 Lincoln LS Logo

Related Topics:

593 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...