Question about 1999 Daewoo Lanos

1 Answer

Daewoo lanos im trying to change rear wheel bearings on a daewwo lanos. ive removed the pin, the nut, the front bearing but the hub will not come off. it springs back if i pull from the top but there is no movement on the bottom at all. what am i doing wrong. thanks .tony

Posted by on

1 Answer

Your brakes are keeping i on the dum try a puller and a hammer

Posted on Oct 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

How to fit front wheel bearings Which brand to use for quality


If the car is front wheel drive a puller is required to dismantle the hub a rather involved job better left to a mechanic .If rear wheel drive do the following. ( Applies to front wheel drive also.) Chock rear wheels,loosen front wheel nuts, jack up car, fit safety stands,remove wheel , remove grease cap from axle. remove split pin or locking nut on axle ,Remove hub, with a punch drive out the grease seal ,the tapered cone bearings can now be removed, the 2 bearing cups still in the housing will have to be pressed out ,all old grease has to be cleaned out. the new cones must be repacked with high temp bearing grease . tap in the seal with the lip facing inwards , slide on the hub fit the outer cone to the axle , the spacer and nut goes on next, tighten the nut to seat the bearings , spin the hub make sure its free to spin, back off the nut one eighth of a turn fit a new split pin or lock tab. fit grease cap and road wheel.

Jul 27, 2014 | Cars & Trucks

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

How do i change the front wheel bearrings on a 1999 sonoma 2 wheel drive?


The bearing is in the hub.. Here are some instructions for that:
  • The wheel bearing is installed in the wheel hub assembly and is serviced by replacement only.

  • You may need Torx sockets to remove the bearing assembly bolts.


  • Raise and support the front of the vehicle safely using jackstands.

    Remove the tire and wheel assembly.

  • At the wheel hub, remove the cotter pin and retainer, then loosen and remove the castle nut and the thrust washer. In order to hold the hub from turning when loosening the nut, insert a drift through the caliper and into the rotor vanes. Remove the brake caliper and support it aside using wire or a coat hanger. Make sure the brake line is not stretched or damaged.

  • Remove the brake rotor from the wheel hub.

  • Remove the bolts retaining the hub/bearing assembly to the knuckle, then carefully pull the assembly from the splined end of the halfshaft. If available, use J-28733-A or B, or an equivalent spindle remover to prevent damage to the shaft or hub/bearing assembly.


  • Remove the cotter pin from the drive axle end nut and retainer


    Remove the retainer for access to the end nut


    Loosen the drive axle nut-here the caliper is installed so a drift could be inserted to keep the disc from spinning



  • Read more: I want to replace my S10 front wheel bearing. My manual ... - JustAnswer http://www.justanswer.com/chevy/0jwks-want-replace-s10-front-wheel-bearing-manual.html#ixzz1hl5SCxBf

    Dec 26, 2011 | 1999 GMC Sonoma

    3 Answers

    I cant get the rear hub off my 97 tercel how do i get it off im trying to change the bearings


    remove the rear wheels
    remove the dust cap
    remove the cotter pin
    loose the nut
    be careful when you install, because you must torque and adjust the nut. if it's done incorrectly it will damage the bearing or the wheel can come off!

    Mar 08, 2010 | 1997 Toyota Tercel

    1 Answer

    Severe bearing noise from front wheel bearing/cv joint area.Cv joint still lubricated,I tend to think axle support bearing is dry & on the way out,but only assuming.How does front wheel bearing come out of...


    you have to replace bearing and hub as a unit.you have to remove remove brakes and caliper rotor set them aside dont disconnect brake line. get a piece of clothes rack wire to hold brake caliper .do not let it hang by brake hose. you got to remove hub nut. best way to do that is loosen it a litttle while tire still on weight of car keep wheel from turning .

    May 03, 2009 | 1999 Daewoo Lanos

    1 Answer

    I am trying to get the wheel assembly apart to change the front bearings on a 1996 mercury villiger


    http://groups.yahoo.com/group/villagerquest/

    9ad2184.gif
    Item Part Number Description 1 — Cotter Pin 2 — Nut Retainer 3 1131 Insulator 4 3B477 Front Axle Wheel Hub Retainer 5 1195 Front Wheel Outer Bearing Retainer Washer 6 1104 Wheel Hub 7 1107 Lug Bolt 8 3K050 Snap Ring 9 3123 Front Wheel Bearing 10 2K004 Front Disc Brake Rotor Shield 11 3130 Front Wheel Knuckle

    Wheel Hub, Wheel Knuckle and Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Tie Rod End Separator T85M-3395-A
    Removal
    1. Raise and support the vehicle.
    2. Remove the wheel (1007) and tire assembly.
    3. NOTE: It is not necessary to disconnect the front brake hose (2078).

      Remove the disc brake caliper (2B120) and suspend it with mechanic's wire out of the way. Refer to Section 06-03 for the removal procedure.
    4. Remove the front disc brake rotor (1125).
    5. Remove and discard the cotter pin.
    6. Remove the nut retainer and insulator.
    7. Remove the front axle wheel hub retainer (3B477) and the front wheel outer bearing retainer washer (1195).




    8. Remove and discard the cotter pin from the front suspension lower arm ball joint (3050).
    9. Loosen the front suspension lower arm ball joint nut until it contacts the front wheel driveshaft joint.


      stv~us~en~file=f8063b.gif~gen~ref.gif

    10. Strike the front wheel knuckle with a hammer while pulling down on the front suspension lower arm (3078) until the front suspension lower arm ball joint separates from the front wheel knuckle.




    11. Remove the front suspension lower arm ball joint nut.




    12. Remove the front suspension lower arm ball joint from the front wheel knuckle.
    13. Remove and discard the cotter pin.




    14. Remove the tie rod end nut.




    15. Use Tie Rod End Separator T85M-3395-A to separate the tie rod end (3A130) from the front wheel knuckle.




    16. Remove the front brake anti-lock sensor bolt.




    17. Remove the two front shock absorber-to-front wheel knuckle nuts.




    18. Remove the two front shock absorber-to-front wheel knuckle bolts.
    19. Remove the front shock absorber (18124) from the front wheel knuckle.
    20. Use 2-Jaw Puller D80L-1002-L, or equivalent, to separate the front wheel driveshaft and joint (3B436) from the front wheel knuckle.
    21. Remove the front wheel hub, front wheel knuckle and front wheel bearing as an assembly from the vehicle.
    22. If necessary, match mark and remove the steering stop bolt and steering stop bolt jam nut from the front wheel knuckle.




    Installation
    1. Position the front wheel hub, front wheel knuckle and front wheel bearing as an assembly on the front wheel driveshaft and joint.
    1. Install the front wheel knuckle into the front shock absorber.
    1. Install the two front shock absorber-to-front wheel knuckle bolts.
    1. Install the two front shock absorber-to-front wheel knuckle nuts. Tighten the front shock absorber-to-front wheel knuckle nuts to 113-123 Nm (83-91 lb-ft).

    Apr 10, 2009 | 1996 Mercury Villager

    1 Answer

    Replacing front wheel ujoint on 2001 ram dodge 1500


    HUB BEARING AND AXLE SHAFT REMOVAL
    1. Raise and support the vehicle.
    2. Remove the wheel and tire assembly.
    3. Remove the brake components from the axle, Refer toBrakes.
    4. Remove the cotter pin and axle hub nut.
    5. Remove the hub to knuckle bolts Hub and Knuckle Remove the hub bearing from the steering knuckle and axle shaft
    6. Remove the brake dust shield.
    7. Remove the axle shaft from the housing. Avoid damaging the axle shaft oil seal.
    INSTALLATION
    1. Clean the axle shaft and apply a thin film of Mopar Wheel Bearing Grease to the shaft splines, seal contact surface, hub bore. Install the axle shaft into the housing and differential side gears. Avoid damaging the axle shaft oil seals in the differential.
    2. Install dust shield and hub bearing on knuckle.
    3. Install the hub bearing to knuckle bolts and tighten to 170 N·m (125 ft. lbs.) torque.
    4. Install the axle washer and nut, tighten nut to 237 N·m (175 ft. lbs.) torque. Align nut to next cotter pin hole and install new cotter pin.
    5. Install the brake components, Refer toBrakes.
    6. Install the wheel and tire assembly.
    7. Remove support and lower the vehicle. 8014d67b.gif

    Feb 26, 2009 | 1996 Dodge Ram 1500 Club Cab

    1 Answer

    How to replace front wheel bearings on 2000 Daewoo Lanos


    they come as a whole assembly hub and all

    Feb 15, 2009 | 2000 Daewoo Lanos

    Not finding what you are looking for?
    1999 Daewoo Lanos Logo

    297 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Daewoo Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Are you a Daewoo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...