Question about 1993 Mazda B-Series

1 Answer

Mazda Bounty Ute B2 series 1993

How do I remove the back brake rotor? It just won't budge even when all the screws have been taken off? Thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 26 Answers

If your replacing them then just go ahead and pound them off with a hammer, if you are getting them turned or some thing and need to replace, spray some thing like pb penetrating luve on the back where it meets the hub and let it soak for a while then pound with a rubber mallet.

Posted on Oct 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have mazda bounty ute runs rough on start up have replaced glow plugs


have the injectors tested as they may not be atomising as they should be. Check for air in the system

Jan 20, 2014 | Cars & Trucks

Tip

Mazda brake mod.


Hi all, this is my first post so my apoligies if its out of order,can anyone give any tips on converting the front drum brakes on my Mazda 1000 ute 74 model to disc brakes,any assistance greatly apreciated, tks. jon.

on May 29, 2008 | 1991 Mazda B-Series

1 Answer

Removing the disc brake caliper and rotor on a 1993 Mazda protege if it is stuck


To replace the lug nut studs you will indeed have to remove the brake caliper, brake rotor, and hub nut, then the hub.

If you post an email (get a temp address if you like from Hotmail) I will send you a workshop manual.

Jun 01, 2012 | 1993 Mazda Protege

1 Answer

How to take back rotors off a 1994 honda civic.


PATH: Brakes > Front Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and support the front of the vehicle on jackstands. Remove the front wheels.
  2. Remove the caliper assembly; do not let the caliper assembly hang by the brake hose, instead support it with a piece of wire looped around the front spring or control arm.
  3. Remove the retaining screw from the brake rotor and remove the rotor from the hub.

An impact driver, No. 3 phillips screwdriver bit, and a hammer may be needed to remove the retaining screw. It is fairly easy to destroy the screw slots using an ordinary phillips screwdriver to remove the tightly driven screw (see photo).

  1. To install the disc, replace the disc on the hub, screw in the retaining screw and replace the caliper assembly.
edc2fe7.gif
PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

4d85ad3.gif

Sep 15, 2010 | 1994 Honda Civic

1 Answer

Mazda bounty hazards go when i indicate.


Try to replace hazard light switch.

Apr 27, 2010 | 1993 Mazda B-Series

1 Answer

Replacing a clutch slave cylinder on a mazda brave ute


You have to disassemble the transmission to the cylinder auxiliary accceder since this is mounted inside the housing of the transmission and is attached with 2 screws. Thanks

Feb 27, 2010 | 2003 Mazda B-Series

1 Answer

How to replace front rotors


You'll need to take the wheel bearings off. the rotors are bolted to the hub and the bolts are located in the back of the hub thus having to remove the wheel bearings and removed the hub/rotor assy.

Apr 26, 2009 | Nissan Frontier Cars & Trucks

1 Answer

I have a 1995 mazda 323 and it has been sitting for 6 months, was it good condition when i parked it. I realize the battery is dead, but it won't even budge when we try to push it in neutral, what could be...


Emergency brake could be stuck in the "ON" position. try rocking the car forward and backward.
Also engage the "E" brake and disengage multiple times to try get it unstuck.

Jan 19, 2009 | 1993 Mazda 323

1 Answer

Front brake mod.-drums to discs 1974 mazda 1000 ute.


I recommend getting a conversion kit, if there is one availiable, and following the installation instructions.

Aug 30, 2008 | 1991 Mazda B-Series

Not finding what you are looking for?
1993 Mazda B-Series Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...