Question about 2006 Toyota Sienna

1 Answer

Back door panel removal

Got a slight dent on the back of my 2006 toyota sienna xle and I believe if i can just remove the back door panel, I should be able to push it back the dent without problem. please give me guidance on how to take of the panel.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 SIENNA XLE SEEMS HOT AIR DOOR NOT CLOSING ALL THE WAY. HOW DO I REMOVE THE LOWER FINISH PANEL TO INSPECT THE SERVO MOTOR AND PLASTIC ARMS?


Remove the under dash panel screws

I always check scan tool data for that module, to
see if there is any data,some vehicles do & some don't

Then you look at manufacture prints, before you go under
the dash

Have to know what things look like & where they are

Need to find the problem first

Then go after the correct motor/servo

Nov 23, 2014 | 2001 Toyota Sienna

1 Answer

I have 2002 toyota sienna XLE. I can use key to control the power sliding door opening and closing when the door is not closed. However, when the door is close, I can not use key to control it. I can only...


the noise you can hear is the lock/opening actuater, have to strip out door panel and see if the actuater mechanism is intact, and operate as before and look to see what part is trying to move, it may just need lubricating but be prepared to have to have new lock actuator

May 03, 2014 | 2006 Toyota Sienna

1 Answer

O5 xle sienna driver's power window stuck open and tipped, also door handle not working


the window regulatore is bad and maybe the track is broke .you can access this by removing the interior door pannel.good luck

Mar 21, 2013 | 2005 Toyota Sienna XLE

1 Answer

Rear door on 2001 sienna won't open


The door handle might be broken, you need a new part. I got mine online for $40. keywords: 2001 2002 2003 2004 2005 2006 2007 Toyota Sequoia Metal Lift Gate Exterior Door Handle for Rear Outside Van Tailgate Handle. You need to remove the back door panel to replace this.

Mar 06, 2010 | 2001 Toyota Sienna

1 Answer

Power door light in dash stays on in my 99 Sienna XLE. The


it sounds like there is a shorting wire some where

Aug 24, 2009 | 1999 Toyota Sienna

1 Answer

Both manual sliding doors on my Toyota Sienna will not open


If you can remove the inner door panel you will see a maze of cables running to the various locking points on the sliding door. If the cable going to the FRONT latch on the sliding door is broken (or in my case, simply dislodged inside the door) the door acts as if it is frozen shut.

The front cable is short, and easily replaced even by a newbie mechanic.

May 27, 2009 | 2004 Toyota Sienna

1 Answer

Toyota Sienna bumper dent


These vans have a styrofoam bumper wrapped in semi-rigid plastic. When you dented the bumper you probably dented the styrofoam as well, so depending on how deep the dent is you may not be able to bring it back to normal.

The surest way to fix the dent would be to remove the bumper by unbolting it, then taking out the styrofoam and pushing out the dent.

Apr 03, 2009 | 2006 Toyota Sienna

1 Answer

04 toyota sienna xle driver side sliding door not opening


You need a motor assembly for the power door. It comes with the gears and cables all as one assembly. It requires taking apart the sliding door from the inside. Removing the door panel, door glass, window regulator and motor assembly to gain access to the unit. This is not a job for a novice, and can be a costly repair. Check around for the best price from a place that has experience in Toyota sliding doors.
You cannot just replace a broken cable.

Feb 26, 2009 | 2004 Toyota Sienna

3 Answers

Replacing RH Side view mirror on a 2006 Toyota Sienna


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Jul 29, 2008 | 2006 Toyota Sienna

Not finding what you are looking for?
2006 Toyota Sienna Logo

840 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...