Question about 1991 Mazda 323

1 Answer

91 mazda gtx

Hey can you please tell me what the torque settings for the head bolts are on the bpt motor

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

On a mazda gtx (4x4 turbo) 1840cc
oil bolts and tighten in 3 even stages

30 ft lbs or 60nm
40 ft lbs or 70nm
60 ft lbs or 81nm

torque sequence is:

inlet side
8 4 2 5 9
10 6 1 3 7
exaust side

Posted on Dec 21, 2008

  • Paul Kear Ufc
    Paul Kear Ufc Jan 24, 2014

    Does a starter motor hav to earth wires on the loom?

  • Paul Kear Ufc
    Paul Kear Ufc Jan 24, 2014

    Can i send a email photo to sum1?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the head bolt Torque settings for Ford laser 2002 dohc ZL on block. 1.6l


go google and type in torque settings for (your engine)
There will be pages of settings and diagrams as to how to pull it down

Mar 17, 2015 | Ford Cars & Trucks

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

2000 model mazda 323 astina cylinder head bolt torque specs


Three stages with new bolts (a must), 1st 60 pounds, then 70 pounds then final torque is 80 FT Pounds.

Feb 16, 2012 | Mazda 323 Cars & Trucks

1 Answer

What are the torque specs of the head bolts of a Mazda protege 94


step 1 17-19 ft/lb
step 2 90 degrees
step 3 additional 90 degrees
engine uses Torque To Yield head bolts
New head bolts must be used when cylinder head is replaced or re-installed

stockam auto

Jul 05, 2011 | 1994 Mazda Protege

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Can you tell me the torque spec.on head bolts for a 1985 ltd 3.8 thank you


Six IN LINE - 6L

zjlimited_510.jpg

Fig.: Cylinder head torque sequence - 6 -cylinder engine



Cylinder head torquing should proceed in three steps and in the prescribed order. Tighten them first to 50-55 ft. lbs. (65-71 Nm), then give them a second tightening to 60-65 ft. lbs. (78-84 Nm). The final step is to 70-75 ft. lbs. (91-97 Nm), at which they should remain undisturbed.


Six IN V - 6V

zjlimited_511.jpg

Fig.: Cylinder head bolt torque sequence - 6 -cylinder engine

Tighten the head, according to the illustrated sequence in three progressive steps. Tighten the bolts to 50-55 ft. lbs. (68-74 Nm), then 60-65 ft. lbs. (81-88 Nm) and finally to 75 ft. lbs. (102 Nm).


Hope this helps (remember to rate and commene this answer).

Jan 19, 2011 | 1985 Ford LTD

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs


I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

1 Answer

94 mazda B3000 3.0L cylinder head torque specs


Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Sep 17, 2009 | 1994 Mazda 2WD B Series Pickup

4 Answers

Torque wrench settings


please understand there are a lot of items on a car that require torque settings every thing from the lug nuts to every engine bolt, and transbolt. please be more specific

Jul 03, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
1991 Mazda 323 Logo

414 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...