Question about 1995 Chevrolet Blazer

2 Answers

No power after installing new head gaskets

Truck starts first click and engine run nice at idel and can be reved up with no proplem but when put in gear it has no power? Hope you can help?Thank you.kennie302@hotmail.com

Posted by on

  • kennie302 Oct 17, 2008

    Could it be timing? or a pluged up converter? or ?Hope someone can help.Thank you.

  • kennie302 Nov 08, 2008

    Thank you for your help and its was the timing .Thanks again Kennie

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

Need to check timing. have you checked compression since head job? low compression will cause this

Posted on Oct 17, 2008

  • TripleTauto
    TripleTauto Nov 10, 2008

    glad to help please rate as fixya

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Check transmision oil lever if its aut., it a trans. pressure problem , pump, converter .
if its a stick tranny check your timing on your ignition system /distributor

Posted on Oct 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blown Head gasket


A leaking head gasket would cause oil to leak into the coolant or coolant into the oil pan, also coolant into the cylinders and compression into the cooling system.
Lack of coolant would not keep the engine from starting but coolant in the cylinders could foul the spark plugs.
If you take the radiator cap off and can see bubbles in the coolant when the engine is running, or the radiator builds up an excessive amount of pressure, it could be the head gasket.
You could remove the thermostat to make sure it is not stuck closed.
The only way to know for sure if the head gasket is leaking is to take the cyl head off and inspect it.

Aug 17, 2012 | 1992 Nissan Pickup

2 Answers

Truck has been in shop twice 1 Ford dealership and 1 Chevy dealership, it started out with an oil pump out , to the timing chain broke to a total of $5000 and truck is still doing the same thing. The...


Someone is scamming you BAD. If you needed a new oil pump, your engine would be long toasted by now. If your timing chain BROKE, it would not even be running. I'm afraid by this point, you may have to get a new engine, just because of mechanic's incompetence, but let's first try and sort out what is going on here. First of all: Is your Ford pre ~1989? If so, it probably has a carburetor, or the electronic so-called carburetor, that has been misadjusted, and is shaking the truck. That would be nice, as it is an easy, and a relatively cheap fix (Readjust, or if all fails, replace carb). If it is post 1989, you could have a failed Electronic Fuel Injection system, that it would be good to have a mechanic with an OBDII port reader check over. You might also have the ignition system tested for a good spark, and have it tuned correctly (Again, assuming older, non-computer controlled.) Finally, if all else fails, have your vehicle tested for a cracked block/head/head gasket.

May 30, 2011 | Ford F-250 Cars & Trucks

1 Answer

On idel ok when reving up very top end rattle have been told the block is a 204e and head is a 205e could that be the problem


Yes!
If you build an engine like this, you must use the composite head gasket from the 204 engine or you will have a heavy top end rattle!

Great question. B204 and B234 engines have negative deck heights. (the piston sticks out of the block a bit, so you need a thicker head gasket.

Apr 12, 2011 | Saab 9 3 Cars & Trucks

1 Answer

Hello i have a 2000 toyota 4runner limited 4x4 . i live in maine and when i start the truck up in the morning to go to work, after the truck warms up it puts out nice heat. but after i drive it for 10...


bleed cooling system.run engine with red cap off till up to temp.replace cap before turning off engine.might have to add more coolant while running.

Feb 13, 2011 | 2000 Toyota 4Runner

2 Answers

I submitted a questions earlier and got a response...thanks! But wanted to add a more info: My 1995 Toyota Tacoma LX (2.4 Liter) was running hot. Last week I had a new radiator installed because it was...


When you drive any overheating vehicle, especially those with aluminum heads, you run a high risk of the heads warping which results in head gasket failure (evidenced by white smoke from the exhaust)
Your repair should be to remove the heads, have them dye tested at a machine shop and checked for straightness (cut if necessary).
Replace the head gaskets and all other gaskets involved in removal.
Your catalytic converter may or may not need replacement but that can only be determined after the gaskets have been replaced and the engine problem is gone. i strongly advise that you change the engine oil after the repair as well to remove any contamination from there as well.
I'd drain the oil before even putting a wrench on the engine. If you find a large amount of coolant in the oil, you may already have destroyed the bearings on the crankshaft making any further repair useless.
If you find no coolant in there, leave the drain plug out so any coolant that gets in the pan during the repair drains out. Attach a warning note to the steering wheel so when you are finished, you don't forget and start the engine without oil in it!! (seen that done too many times to not mention it)

Feb 08, 2011 | 1995 Toyota Tacoma

2 Answers

1988 S-10 2.5L- Brand new cyl head & gasket- new radiator- water pump is working and I'm getting air pushing through the radiator. Disconected the upper hose to the rad to see if pump was working after...


im thinking the thermostat is in wrong, or the intake gaskets were reversed during installation, they only flow one way, cutting flow to the water pump

Jun 15, 2010 | 1988 Chevrolet S-10

1 Answer

What causes oil to get in antifreeze


Driving the truck without a thermostat won't necessarily hurt the engine. It will take longer to get heat and it will be sporadic because the coolant is always circulating. Oil in antifreeze could come from 2 places, transmission cooler in rad if you have an automatic. The lines inside will occasionally start leaking. The other is from the engine, usually a head gasket leaking. My suspicion is that you have a leaking head gasket. This would explain the over heating with oil in the coolant. Take it in and get a pressure test on the rad or a compression test on the engine. This should confirm or eliminate the head gasket. Hope this helps.

Jan 31, 2010 | 1988 Mazda B2200

1 Answer

Blown head gasket or not?


check oil dip stick for water/antifreeze and radiator for oil in antifreeze but usually alot of white smoke-steam from tailpipe usually indicates head gasket blue smoke means oil black smoke carbon

Sep 29, 2009 | 1993 Acura Integra Hatchback

1 Answer

Started with head gasket problem, tried to flush system..


You more then likely have more then one issue. You can pull the plugs to see if the engine is hydra locked, It sounds like you lost power so check that the battery is still fully charged, check the connections at the battery, engine block, and starter. Sounds like something just got wet or it was a coincidence. I never suggest to anyone, the use of stop leak.

May 23, 2009 | 1992 GMC Sonoma

1 Answer

1998 dodge ram 1500 2w/d fuel enjected


i would put new head gaskets and get the heads check out for hairline cracks and possibly shaved

Jan 11, 2009 | 1989 Dodge D150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...