Driver side low beam headlight installation

Here's a link on replacing your light bulb on your VW. Sparky Answers 2001 VW Beetle Changing The Low Beam Headlight Bulb HERE'S A VIDEO,ALSO How To Change Head Light Bulb VW Beetle

bad connection or bad earth check all connection or bulb

I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics

Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)

Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Mercury Sable - YouTube

? 6:06
www.youtube.com/watch?v=Mlb1V5vNgFM
Jan 3, 2012 - Uploaded by 1A Auto Parts http://www.1aauto.com/1A/HeadLights/Mercury/Sable/1ALHP00223 ... Find out why. Close. How to Install Replace Headlight and Bulb Mercury Sable 00-05 ... How To Install Replace Fog Lightand Bulb 00-03 Mercury Sable

try the fuses or wire fuse links , the only other thing in the circuit is the wires broken or the light low switch is bad

There should be separate fuses for high and low beams on a Prius. If one of your headlight bulbs is bad, it could have blown the low-beam fuse. Check for blown fuses behind driver's side headlight fuse panel. If new one blows, replace headlight bulbs and try again.

On 2004-2009 Prius, driver's side headlamp bulb can be replaced by removing hold down screws and folding fuse panel upward to access rear of headlight assembly. Large round cover with 3 tabs unscrews about 1/4 turn to remove. It's really tight and held by friction of large O-ring so it'll take some muscle but it will eventually give. Be careful replacing bulbs as metal clips can be easily installed incorrectly resulting in tilted headlight beam. 3-tabs must rest on flat surfaces on mounting area before spring clip can be latched in place. 3-prong plug can be wiggles sideways/up and down to remove from bulb.

There is one unit on that side that contains both - - take it to Advance Auto - they will install the new one purchased from them - FREE.
Gary @ Fix Ya

Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.

If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.

If its not working now then your cursed, seek a witch doctor.

The low beam bulb needs to be replaced. Go to an autozone store as they will sell you the bulb, and even assist you in their parking lot with installing it.

It's a bulb replacement. If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. Installation of the new one is the reverse. Just be SURE not to touch the glass part of the bulb. Skin oils can cause a halogen bulb to burn very hot and burn out very quickly. If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it.