Question about 2001 Chrysler Town & Country

4 Answers

Turn signals blink on the wrong side

When I put the turn signal lever in the right turn position, the left signal blinks. When I put it in the left position, the right signal blinks. Occasionally, nothing happens when put in either position. What could be causing this? There are no computer codes present. Thanks.

Posted by on

  • pangen-34101 Oct 17, 2008

    This on a 2001 Town & Country mini-van.

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I dad the same problem and I replaced the multi function switch the does the wipers and the signals. After a while they wear out internally and the contacts become jared so they malfunction. I want to say the new dealer part only cost like $40 or so

Posted on May 07, 2009

Adjust your steering up /down as it may lossen the pinched wires or switch. had same problem but now it OK.

Posted on Oct 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 60,867 Answers

Your signals don't go through any computer (that is next year, HA,HA), either a connector is hooked up wrong (crossed) to the lights or the wires were worked on and not put back together correctly.

Posted on Oct 20, 2008

  • greg christopher
    greg christopher Nov 17, 2016

    I've got a 1990 Chevy truck 1500 and my turn signals are blinking on wrong side if I go right it blinks left and etc...what could be my problem fix? let me know thanks

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Do you have a trailer hitch? If you do, the problem may be in the wiring for your trailer lights. I use to work for u-haul and installed $75,000 worth of hitches in one year. the vehicle in your picture take a power module to work your trailer lights. this means a device that takes power from the battery to make your trailer lights work, if you hook up trailer lights to the existing vehicle wiring it will cause a lamp-out sensor failure. If you have this wiring check for normal operation with a test light. If you go to u-haul they probably will inspect your wiring for free. If the device was installed properly, it still can malfunction and probably will sooner or later due to condensation inside the power module. I replaced many of these while working for u-haul.

Posted on Nov 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn lights blink with hazards but not with turn signal..flasher replaced. is It the multifunction lever then??


There should be a turn signal flasher and a hazard flasher. They are two different parts. If you replaced the hazard flasher and not the turn signal flasher than I would start by replacing the turn signal flasher.

One thing you can do once you find the turn signal flasher is to unplug it and use a jumper wire between the two pins of the connector then turn the key to the run position and place the turn signal lever in the left or right position. If the turn signal lights know light up than the turn signal flasher is the problem

Sep 09, 2014 | 1997 Oldsmobile Cutlass Supreme

2 Answers

1999 buick lesabre my right signal doesnt blink it stays solid , my left turn signal blinks fine i have to manually blink the right side every turn , i put the hazard lights on and the front left and right...


The easiest thing for you to do would be to replace the bulbs that are on that circuit. You should have one or two bulbs with a double filament, one for the brake and turn signal and one for the tail light.
If that does not fix the problem, someone will need to check the circuit for power from the turn signal switch. It takes all of the lights on one side to make the turn signal flash.

May 16, 2013 | 1999 Buick LeSabre Custom

1 Answer

92 buick skylark right side blinker does not work the bulbs are good left side works. you can here the turn signal quick blink noise when using right turn signal


check the front bulbs .

turn on the LEFT (fullt functioning ) turn signal ,
get out of the car and look at what lights are blinking in the front.
now turn on the right (broken) signal and note which lights are NOT blinking that had been on the fully functioning signal indicator.

Sep 28, 2011 | Cars & Trucks

1 Answer

Left rear brake,signal donot work,right rear side works,when i turn lever to make left turn,lite on dash board,blinks rapidly, replaced bulb and checked fuse


Most likely a bad multifunction switch (turn signal switch), try wiggling the turn signal lever while it is turned to the left and see ifit ever works.This is extremely common problem on fords,but not the only one, could also be a broken wire ,bad ground or a bad light socket.

Jan 30, 2011 | 2004 Ford F150

2 Answers

Left turn signal is really fast


bad or wrong bulb. all of the bulbs must be good even the side markers if they blink when turn signal is on.

Sep 30, 2010 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

1994 BUICK SKYLARK- MY TURN SIGNALS ARENT WORKING, AND NOW ALL OF A SUDDEN MY LEFT TURN SIGNAL IS FROZEN IN THE ON POSITION....WE ALSO PURCHASED AND ELECTRICAL FLASHER THINKING THAT MIGHT HELP THE TURN...


If the turn signal is stuck in the position,then the turn signal switch is bad,now if the turn signal just stays on,and does not blink,and the turn signal lever returns to the neutral position,then it is a bulb that is bad on that side on the car,,front,side,or rear.If the turn signal moves to the left position,and returns back to the neutral position,it is ok,unless it is blinking,then it would be bad,the turn signal switch.

Oct 26, 2009 | 1994 Buick Skylark

1 Answer

Drivers side turn signals will not function properly even though all lamps are burning


do you mean they dont blink? only on left side, but do blink on the right? put the hazrd flashers on and see if all works., if OK , then may be the turn signal switch of only the left side does not blink???

Oct 04, 2009 | 2004 Pontiac Grand Prix

1 Answer

Jeep Liberty Left Rear Turn Signal Not Working


sounds like the bulb you have is the wrong resistance the new noen bulbs will do this

Nov 16, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

594 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...