Question about 1994 Nissan Maxima

2 Answers

1994 nissan maxima

Car starts and drives but soon as I come to a stop it hesitates like its not getting gas it has a 3.0 dual over head cam its like its miss firing .after a while i can get it going and up to speed but this happens every time i stop

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Adjust your idle control valve (there is a setscrew under the rubber cap- you'll see it) also check the ignition system (distributor cap, coil, wires) fuel and air filters should be changed if not (replace every 2 years or so)

Posted on Feb 17, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You may have a loose spark plug wire or your main spark plug rotor spinner might be bad its where all the plugs join together. Left side of maxima.

Bryon

Posted on Oct 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to be sure to set heads back right with compression stroke on 1994 nissan maxima


I guess you are asking how to set cam timing. If you mess this up you can do real damage, so best would be buy a cheap shop manual at parts store.

Feb 09, 2015 | 1994 Nissan Maxima

1 Answer

Can you give me steps on how to remove the cylinder heads on 91 nissan maxima 3.0 GEE dual overhead cam plz...thanks


Don't attempt it. It is not for the DIYer. There are very detailed procedures to follow and getting the timing right is is tricky. If you do attempt it buy a good manual and follow it closely.

Aug 18, 2014 | 1991 Nissan Maxima

1 Answer

1994 Nissan Maxima timing belt intact. Distributor rotor not spinning. What could be the cause?


Use no. 27 ring spanner to check if your pulley on the crank drives. Suspect your right cam shaft is either seized or broken.

Jan 17, 2013 | 1994 Nissan Maxima

1 Answer

Hello, Where is the Cam position sensor located on a 2004 Nissan maxima bank 1 located?


3.5litre V6 Front wheel drive, the cam position sensor is in the back of the cylinder head above the transmission. bank one is the front bank, nearest to the grill. the cam sensor is held into the head with a 10mm bolt, has one wireing connector with 3 wires in it. the sensor is sort of round with a leg off one side for the bolt the secure.
may need to remove the engine cover to see it. it is held down with allen key bolts.

Mar 25, 2011 | 2004 Nissan Maxima

1 Answer

1996 nissan maxima hesitates to start on cold start, i have to press gas till it turns on, i have changed spark plug's & coil packs, have put sea foam in gas & intake .


sea foam ?? what is this please never heard of it before ,anyway have checked out the autochoke device ,their should be a sensor on the cylinder head thats is a temperature gauge and it turns on the autochoke and this circuit has a problem but as to exactly what is the problem i couldnt say without a detailed inspection

Feb 27, 2011 | 1996 Nissan Maxima

1 Answer

I have a 94 nissan maxima and when it rains the car just cranks but doesnt start and as soon as it gets warm out it starts. why?


the windshied may have a leak and could be getting on the ECM which is located under the dash in front of the console. there is a little cover on the passanger side and the drivers side by the gas pedal

Mar 31, 2010 | 1994 Nissan Maxima

1 Answer

Car smokes, wont stay running


You most likely blew a cylinder head gasket.

Aug 16, 2009 | 1989 Nissan Maxima

3 Answers

How can i tell if my 1994 nissan maxima is single or dual cam?


Pretty easy to tell even without taking the valve cover off.
If it is a dual cam, then the spark plugs are lined up right down the middle, between the 2 cams.
Which is optimal.
If it is a single cam, the plugs have to be off to one side, on an angle.
Which is not as good.

Aug 09, 2009 | Nissan Maxima Cars & Trucks

1 Answer

2004 nissan maxima SE with 61,000 miles. Driving


no it is not it could be the trans a vavle or a cracked head

Mar 15, 2009 | 2004 Nissan Maxima

1 Answer

My 2002 Nissan Maxima hesitates to start


if vehicle hesitates to start do you mean long cranking time (posible fuel pump) or no crank at all then suddenly starts then it is possible starter solenoid (notorious) - complete starter assembly needs replacement.

Aug 20, 2008 | 2002 Nissan Maxima

Not finding what you are looking for?
1994 Nissan Maxima Logo

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...