Question about 2006 Ford Laser

1 Answer

Weheel bearings 1988 KE Laser


My left rear whell bearings are going on the LAser. Are they relatively easy to replace? Are there any tricks? Do you need a press to remove and replace?

Thanks in advance

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 426 Answers

They are easy to replace but should be done at work shop unless you have the tools to remove and install the bearing outer cone,a press is not required They are easy to damage when refitting.If you wish to know more and attempt it yourself you will need a half inch socket set Metric and imperial,a punch,hammer,grease,pliers for the split pin,clean rags,screwdriver to loosen brake shoes off if brake drum doesnt come straight off and a bit of patience.Once youve done it to one side the other will be easier and quicker.Let me know and Ill walk you through it as you do it .

Posted on Oct 17, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I adjust the tappets on a 1986 1.6i ke laser

easy capri laser?? ford , 4cyl in line --- 1 down adjust 8 =9
1 down adjust 7 =9 and so on 8 down adjust 1 =9 whatever you adjust the numbers add up to 9 ,ford laser capri then tappet settings used to be something like 14 inlet and 18 exhaust but as no doubt the rocker fingers are worn and the push rod cups the 12 and 15 may be better

Mar 12, 2015 | 1986 Chrysler Laser

1 Answer

Replacing front axle seals and bearings

I replaced the left front bearings and seals a couple of months back. It is not a problem but be careful as you dismantle the system and of course the reassembly of same. Be sure to replace all bearings and seals as you probably don't want to do this job twice at the cost of parts. No special tricks and relatively easy job. 1601d678-bcb0-4cc6-af13-c2a57bf7d073.jpg

Jun 22, 2014 | 2001 Ford F-250 Super Duty

1 Answer

Remove and install water pump on 1988 ford ke laser

You have to remove your belt ...and fan shroud then remove outer bolts off water pump housing take off replace with new water pump and GASKET, seal gasket with permatex before placing gasket in place then rebolt new water pump on and your golden.....make sure no dirt or debris gets in glad i can help ...

May 25, 2011 | Ford Laser Cars & Trucks

1 Answer

I own a 1988 Toyota 4runner. It has started to make a howling/rubbing noise at random times, and in random drive selection I can hear it at slower speeds. Seems to be from the right front but? I have...

first check the brake pads to see if they are hanging up/sticking if good than recheck ur bearings /hub cv joint new doesnt mean free from defects or u may not have tightened it right and or something failed

Jan 03, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

I need the cylinder head bolt removal and tightening sequence for my 1989 ke ford laser. its a manual transmission if that has any bearing

To remove the bolts,start at the outside and work in,to tighten start at the centre and work out,in a diagonal pattern alternating left to the pattern to work to also when Tightening,start at 25 ft.lbs.then goto 50ft.lbs,then 75 etc.ALWAYS use NEW bolts,cos if one shears you have another problem........

Dec 22, 2010 | Ford Laser Cars & Trucks

1 Answer

Collapsed Rear Wheel Bearing for a Ford KE Laser! How can I fix it?

Tsis is not an easy task to do at home, so I have a link to a site which it expalins the procedure rather well...


Apr 21, 2010 | 2006 Ford Laser

1 Answer

Ke laser ignition problem

Have you replaced the rotor in the dizzy and made sure the the leads are fimly attached to the dizzy cap.

Mar 15, 2009 | 2006 Ford Laser

1 Answer

Alternator for a 1989 masda 323 or ford laser ke

deseo saber las especificaciones tecnicas de la bateria a utilizar en el automovil mzada 323 lx 1.3 , station, año 1989.

Jul 15, 2008 | 1989 Mazda 323

Not finding what you are looking for?
Cars & Trucks Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides