Question about 1992 Mazda MX-3

Open Question

Mazda mx-3 headlight assembly installation

So I finallllyyy found a driver side headlight assembly for my mazda mx-3 and I was wondering how to install it. Is their anything screwy with it or is it just basic in/out. Some basic steps would be helpful too. Thanks! =]

Posted by on

  • Anonymous Mar 29, 2009

    how do i remove and replace the unit

  • Anonymous Mar 29, 2009

    reflector is loose

×

6 Suggested Answers

picatudo
  • 239 Answers

SOURCE: My mazda mx 3 idling high

replace fuel pump inside tank

Posted on Jan 07, 2009


timmybrown
  • 54 Answers

SOURCE: I'm trying to repace the driver's side turn signal - 2002 MPV

if you have ll the screws out then you just need to work it out. there a ball on the lens that pops into a socket on the frame. if it never been removed its a bit of a struggle

Posted on Apr 16, 2009

lilmikew99
  • 105 Answers

SOURCE: headlight aiming too high - how to adjust?

pop your hood open and on flat surface check too see where the beads are in the bubble levels,if they are off then there are 2 adjustments on each headlight,some require special tool they look like little gears on the adjusters. make sure car is on good flat surface

Posted on May 11, 2009

  • 1 Answer

SOURCE: replacing drivers side headlight on 05 mazda 3

Found this answer on:
http://wiki.answers.com/Q/How_do_you_change_low_beam_headlamp_on_a_2005_Mazda_3

Posted on Nov 17, 2009

partyd
  • 141 Answers

SOURCE: Auxiliary audio input for 2008 Mazda MX-5 with Bose sound system

Yes you can add auxiliary or ipod interface also xm radio

go here for more information
http://www.oemautosound.com/c-161-mazda-products.aspx

Posted on Apr 01, 2010

  • 143 Answers

SOURCE: 2009 Mazda 3 found water

heater core inside dash asm. pressure test cooling system and check

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Mk1 Mx5 and my popup lights were working fine till last week, were only one (drivers side) comes up. I can pop the hood and fiddle with the manual light raiser and then it starts to work but its...


Lubricate all the rods and connections you have so there is not as much friction.

The headlights in a Mazda Miata are generally of two types. Some Miatas use the factory "flip up" style headlights, where a motor raises and lowers the headlight assembly out of the front bumper area. When this motor fails or when the headlights are not working properly, you'll need to replace the failed component. Replacement headlights are normally available from Mazda or from most auto parts stores if you need to replace the entire assembly. However, before you replace anything, you need to troubleshoot the problem. check for debris in the path and any loose or frayed wires.

Unfortunatly there is no adjustments, probably a weak motor.

If this was helpful a vote with the thumbs up would be appreciated for the advice.

thanks

Apr 08, 2011 | 1995 Mazda MX-5

2 Answers

Hi I have a mazda mx5 mk3 from the UK and I am looking to change my headlights in order for me to register my car in France. I need to change the full headlight assembly and was wondering if you could...


try fitting stick on beam correctors on the outside of the headlamps you usally buy them from a mazda dealers parts dept a lot cheaper than fitting headlamps and comply with french and uk law once fitted

Feb 24, 2011 | Mazda MX-5 Miata Cars & Trucks

1 Answer

Heater has stopped working


(1) possible blown fuse.
Note that fuses blow for a reason - seek out the reason, or it will blow its new fuse too.

The main fuse block is located inside the left side of the engine compartment near the battery. There is also an interior fuse panel located just above the left side kick panel.

Interior Fuse Panel
The interior fuses simply unplug from the fuse panel. Use the fuse puller tool provided with your car to remove fuses from the panel. The tool is located on the back of the interior fuse panel cover.


(2) possible blower motor dead. See maintenance manual excerpt below.

(3) possible blower motor relay faulty. Location of Blower relay:
Under hood, drivers side, front engine area,rear of headlight housing; relay mounted on drivers side of radiator shroud.


1990-92 Mazda 626 and MX-6
See Figure below

archaeology_8.jpg
  1. Disconnect the negative battery cable.
  2. Remove the glove box and the underdash cover.
  3. Detach the electrical connectors from the blower unit.
  4. Remove the blower unit-to-fire wall attaching bolts and remove the blower unit assembly.
  5. Remove the blower motor fan-to-motor fastener.
  6. Remove the blower motor-to-unit attaching bolts, then remove the motor.
  7. Installation is the reverse of the removal procedure.

Feb 01, 2011 | 1991 Mazda 626

1 Answer

No headlights on 2005 mazda 3


Probably the headlight relay under the hood in drivers side fuse/relay box.
Not sure exactly its location in this box though

Feb 09, 2010 | 2005 Mazda 3

1 Answer

How do I remove the nearside headlight unit on my MX3


first remove the 3 screws linking the metal bracket to the headlight, the the 2 bolts on top, and the last bolt inside the bumper, you will need a flashlight to see, it's not easy to find

good luck

May 16, 2009 | 1995 Mazda MX-3

2 Answers

Need to change headlight on 2003 mazda rx 6


If it is the headlight itself. There may be a cover or shroud on the front of the engin bay. Remove that, may be a combination of clips and screws. If it does not cever the light area, it is even easier. There will probably be 3 screws or nuts, remover these and unplug the electrical to the light. From there you should just be able to pop the light out of place. If you are just replacing the bulbs. Where the power goes into the assembly, turn the clip, may be grey in color and pull out of the headlight assembly and replace the light bulb. But don't touch the new bulb the oils from your skin will damage the bulb.

Apr 22, 2009 | 1994 Mazda MX-6

1 Answer

No heat


I found out that the 626 model has a relay for the blower motor on the drivers side firewall (in engine compartment). Not sure if it's the same location as yours, but a bad relay could be the problem.

Jan 12, 2009 | 1992 Mazda MX-3

1 Answer

Handbrake not engaging!!! ;o(


did you pull the plug out of the back of the calper and adjust the caliper after the new pads were installed?

Nov 15, 2008 | 1992 Mazda MX-3

1 Answer

Headlight retractor


The gears that drive the light to open are worn out, you will need to replace the head light motor assembly, this is common isuue with pop up motorized headlights.

Aug 06, 2008 | 1990 Mazda MX-5

Not finding what you are looking for?
1992 Mazda MX-3 Logo

Related Topics:

571 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...