Question about 2005 Chevrolet Impala

1 Answer

Power steering Where is the power steering filler tube located?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 68 Answers

It should be located around the brake booster and master cylinder hope u find it

Posted on Nov 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the power steering pump?


Hi Brian:
Check this REMOVAL and INSTALLATION procedure... (see Figures 2, 3 and 4)
  1. Position a fluid catch pan under the power steering pump.
  2. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan.
On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  1. Remove the drive belt from the pulley.
  2. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.
When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
2_8_2012_3_52_57_pm.gif

Fig. 2: Installing the pilot bolt

2_8_2012_3_53_39_pm.gif

Fig. 3: Removing the power steering pump pulley



2_8_2012_3_54_28_pm.gif

Fig. 4: Installing the power steering pump pulley

  1. On most models, it may be necessary to unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  2. If equipped, unfasten the power steering filler tube bolt and remove the filler tube.
  3. Remove the rear brace retainers and the brace.
  4. Remove the power steering pump-to-bracket bolts and then remove the pump from the vehicle.
To install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm) 2.2L engines. (50 Nm). On 4.3L engines tighten the bolts to 37 ft. lbs. (50 Nm).
  2. If equipped, install the rear brace and tighten the retainers to 22 ft. lbs. (30 Nm) on 1994-98 2.2L engines. On 1999 2.2L engines, tighten the brace retainers to 37 ft. lbs. On 1994 4.3L models tighten the retainers to 24 ft. lbs. (33 Nm). On 1995-99 4.3L models, tighten the retainers to 31 ft. lbs. (41 Nm).
  3. If removed, install the A/C compressor.
  4. If removed, install the filler tube and its retainer. Tighten the retainer to 15 ft. lbs. (20 Nm).
  5. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end.
When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  1. Properly install the drive belt and, if applicable, adjust the tension.
Be sure to secure any hoses which may get in the way or rub other components.
  1. Remove the caps, then connect the feed and return hoses to the pump.
  2. Properly refill and bleed the power steering system.
  3. Test drive the vehicle.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 08, 2012 | 1996 Chevrolet Blazer

1 Answer

How do you remove the power steering pump from a 2001 Chev Blazer with the 4.3 engine?


4.3L Engine
  1. Position a fluid catch pan under the power steering pump.
  2. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan.

    NOTE

    On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.

  3. Remove the drive belt from the pulley.
  4. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.

    NOTE

    When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.




82f6b07.gif

Installing the pilot bolt



a0959f0.gif

Removing the power steering pump pulley



3c54326.gif

Installing the power steering pump pulley


  1. On most models, it may be necessary to unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  2. If equipped, unfasten the power steering filler tube bolt and remove the filler tube.
  3. Remove the rear brace retainers and the brace.
  4. Remove the power steering pump-to-bracket bolts and then remove the pump from the vehicle.

To install:

  1. Position the pump to the vehicle and secure using the front retaining bolts to 37 ft. lbs. (50 Nm).
  2. If equipped, install the rear brace and tighten the retainers to 31 ft. lbs. (41 Nm).
  3. If removed, install the A/C compressor.
  4. If removed, install the filler tube and its retainer. Tighten the retainer to 15 ft. lbs. (20 Nm).
Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end.

NOTE

When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.


Properly install the drive belt and, if applicable, adjust the tension.

  1. NOTE
  1. Be sure to secure any hoses which may get in the way or rub other components.

  1. Remove the caps, then connect the feed and return hoses to the pump.
  2. Properly refill and bleed the power steering system.
  3. Test drive the vehicle.

Oct 30, 2010 | 2001 Chevrolet Blazer

1 Answer

How do i flush the hydraulic steering system


You really can't flush out the steering system fluid other then siphoning the fluid out of the steering pump reservoir. This is the easy way.
The hard way:
Remove the filler cap from the top of your power steering system then disconnect the reservoir's hose. It should be located on the bottom of the reservoir. The hose can be tough to remove, so make sure you have plenty of patience.

Replace the reservoir's hose with another hose. It should lead to an empty container. You'll use this container to store the old power steering fluid as it leaves the reservoir. Lift the front end of your car off the ground by using a car jack.

Add new power steering fluid to the reservoir. As you add the new lubricant, it will force the old lubricant into the tube you've connected to the bottom of the reservoir.

Climb into the drivers seat and rack your steering wheel back and forth. The wheel should be locked in place, allowing only a slight range of mobility. This will help the extra lubricant within the power steering system to drain.

Watch the empty container. It should fill with old lubricant. Once the old lubricant has been flushed and you see clean fluid replacing it, you've finished the hard part.

Disconnect your hose and move the container. Replace the original reservoir hose. Pour new, clean power steering fluid into the reservoir. Rack your steering wheel a few more times to squeeze out air that might be trapped in the lines. Replace the filer cap and close your done.

Thank you for suing fixya and good luck







Jun 11, 2010 | 1993 Chevrolet Camaro

1 Answer

Cannot find the power steering fill under hood


Look under the hood inside the right fender. The filler will likely have 2 tubes coming off the base - one going to the power steering pump. On some models it can be out of sight under other equipment.

Dec 16, 2009 | 1997 Pontiac Grand Prix

1 Answer

Now toremove power streeing pump



REMOVAL & INSTALLATION

See Figures 2, 3 and 4
  1. Position a fluid catch pan under the power steering pump.
  2. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan.

On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  1. Remove the drive belt from the pulley.
  2. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.

When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.


0900c15280250684.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Installing the pilot bolt


0900c15280250685.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Removing the power steering pump pulley


0900c15280250686.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Installing the power steering pump pulley
  1. On most models, it may be necessary to unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  2. If equipped, unfasten the power steering filler tube bolt and remove the filler tube.
  3. Remove the rear brace retainers and the brace.
  4. Remove the power steering pump-to-bracket bolts and then remove the pump from the vehicle.

To install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm) 2.2L engines. (50 Nm). On 4.3L engines tighten the bolts to 37 ft. lbs. (50 Nm).
  2. If equipped, install the rear brace and tighten the retainers to 22 ft. lbs. (30 Nm) on 1994-98 2.2L engines. On 1999 2.2L engines, tighten the brace retainers to 37 ft. lbs. On 1994 4.3L models tighten the retainers to 24 ft. lbs. (33 Nm). On 1995-99 4.3L models, tighten the retainers to 31 ft. lbs. (41 Nm).
  3. If removed, install the A/C compressor.
  4. If removed, install the filler tube and its retainer. Tighten the retainer to 15 ft. lbs. (20 Nm).
  5. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end.

Jul 05, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Removal and installation of the water pump


3.0L or 3.8L engine?

please rate as fixed if this solves your issue.

Section 03-01B: Engine, 3.8L 1996 Windstar Workshop Manual
IN-VEHICLE SERVICE Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
  1. Drain engine cooling system. Refer to Section 03-03 .
  1. Loosen drive belt tensioner (6B209) and remove drive belt (8620). Refer to Section 03-05 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Disconnect lower radiator hose (8286) from radiator lower hose tube (8291) and radiator (8005).
  1. Disconnect radiator lower hose tube from water pump (8501).
  1. Remove lower nut on both front engine support insulators (6038).
  1. Lower vehicle.
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove generator (GEN) (10346) from power steering pump support (3C511).
  1. Position drain pan and disconnect power steering pressure line from power steering pump (3A674) using Fuel Line Disconnect Tool Set T90T-9550-S.
  1. Remove power steering reservoir filler cap.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If using a prying device to assist in water pump removal, be careful not to damage the mating surfaces.
    Disconnect water bypass hose (8597) and oil cooler hose (6B850) from heater water outlet tube (18663).
  1. Remove retaining bolts and disconnect heater water outlet tube from water pump.
  1. Remove A/C bracket brace.
  1. Attach engine lifting eye to left-hand (front) exhaust manifold (9430).
  1. Attach lifting equipment to engine lifting eye and raise front of engine approximately 51 mm (2.0 inches) to provide necessary clearance for water pump removal.
  1. Remove water pump pulley retaining bolts and water pump pulley (8509).
  1. Remove drive belt tensioner pulley retaining bolt and drive belt tensioner pulley (6B217) from power steering pump support.
  1. Remove power steering pump support retaining bolts and nut. Place power steering pump and support assembly aside in a position to prevent fluid leakage.
  1. Remove water pump retaining bolts and nuts and water pump. Discard used water pump housing gasket (8507).
Installation
  1. NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant.

    Clean gasket surfaces on water pump and engine front cover (6019).
  1. NOTE: The threads of the No. 1 engine front cover retaining stud must be coated with Pipe Sealant with Teflon® D8AZ-19554-A or equivalent meeting Ford specification WSK-M2G350-A2 before installing.

    NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the water pump housing gasket in position.

    Position a new water pump housing gasket on water pump housing sealing surface.
  1. Position water pump on the engine front cover. Install retaining bolts.
  1. Position power steering pump support and install retaining nuts and bolts. Tighten bolts and nuts to 40-55 Nm (30-40 lb-ft).
  1. Install drive belt tensioner pulley and retaining bolt. Tighten bolt to 70-95 Nm (52-70 lb-ft).
  1. Install A/C bracket brace.
  1. Position water pump pulley on water pump hub and install retaining bolts. Tighten bolts to 8.0-11.5 Nm (71-101 lb-in).
  1. Lower engine and disconnect lifting equipment from lifting eye.
  1. Remove lifting eye from exhaust manifold.
  1. Connect heater water outlet tube to water pump and install retaining bolts. Tighten bolts to 8-11.5 Nm (71-101 lb-in).
  1. Connect water bypass hose and oil cooler hose to heater water outlet tube. Tighten clamps securely.
  1. Connect power steering pressure line to power steering pump fitting.
  1. Install power steering reservoir filler cap.
  1. Install generator to power steering pump support. Refer to Section 14-02 .
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Install lower nut on front engine support insulators and tighten retaining nut to 88-119 Nm (65-87 lb-ft). Install lower nut of rear engine support insulator and tighten to 77-104 Nm (56-76 lb-ft).
  1. Connect radiator lower hose tube to water pump. Install retaining bolt and tighten securely.
  1. Connect lower radiator hose to radiator lower hose tube and radiator. Position hose clamps securely. Refer to Section 03-03 .
  1. Lower vehicle.
  1. Position drive belt over drive belt tensioner and release drive belt tensioner. Refer to Section 03-05 .
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: This engine has aluminum cylinder heads (6049) and requires a special corrosion inhibiting coolant to avoid cooling system damage. Refer to Section 03-03 for the coolant specifications.
    Fill and bleed cooling system with specified coolant.
  1. Fill power steering pump reservoir with specified fluid.
  1. Start engine and check for coolant and power steering fluid leaks. Service as necessary.


    Water Pump
581f50d.gif

Apr 13, 2009 | 1996 Ford Windstar

2 Answers

Where is the powersteering pressure switch on a 01 dodge durango


Right next to the power steering filler. it has two wires that come from it..

Apr 08, 2009 | 2001 Dodge Durango

1 Answer

Replace power steering hoses


trace the filler or resiviour clean and run to find leak one side is high pressure so dont mix up,it may hv have 0 rings so renew.when fitted refill filler run and refill as it will go down

Jan 06, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

I am wondering where the power steering pump is located on a 1999 bravada


Your power steering pump is located right in front. You have to take the upper fan shroud off and the serpentine belt.  You will need an a power steering pump pulley remover as well, but I think you can barrow one from auto zone. You will also have to disconnect the pressure and return hoses from the backside of the pump. Then remove the pump mounting fasteners and lift it out of the truck. Also on 99 4.3 liter you need to unbolt the filler tube from the air conditioning compressor.  ( call an auto parts store to see if you air system needs to be decompressed before removing the filler tube)

Nov 25, 2008 | 1999 Oldsmobile Bravada

1 Answer

Power steering fluid


look along the belt to find the pump then the filler cap should be on top of that

Aug 17, 2008 | 2003 Chevrolet Impala

Not finding what you are looking for?
2005 Chevrolet Impala Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...