Question about 2005 Chrysler 300

1 Answer


Posted by on

  • yadayada
    yadayada May 11, 2010

    Should there be?? Go to the dealer and check another car like yours.



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 2005 300 i ws backing out of my driveway and my front bumper fell off. And I also my indicator light won't go off.

Posted on Jan 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Isuzu trooper 2000 signal light passanger side how change the light bulb please help

RIGHT side, front or rear.??????
same as all car, watch youtube and 1000s doing same.
all cars have these ways, looking 1 time solves it,
no photos by you,
look at the lamp.
it has a lens.
  1. if lens has screws they come off.
  2. if body shows, screws, they come off.
  3. if nothing seen above, then its rear entry. you must reach the rear of the light assembly.
  4. if car has fender skirts blocking this, (inside) they must be loosened. ILL not go forward to book pages, until you tell what end of car you are on, gee.

Dec 06, 2016 | 2000 Isuzu Trooper

1 Answer

How to change headlight assembly on a 1997 Isuzu rodeo?

the whole thing, not just a bulb?
no job stated, (light out or collision repairs, must we guess?)
is the car USA car, or that down under HOLDEN car.?

here is the assembly. the new bulb screws in to rear.
the assembly has about 4 screws,
top get to them take work.
gaining access to them removing body panels or fender inside skirts. why not ask your machanic to do this.
or tell symptoms FIRST !


Sep 19, 2015 | Isuzu Cars & Trucks

1 Answer

Where is the horn location under hood of a 2007 mercury mountneer?

Remove the LH front fender splash shield !
Fender Splash Shield Removal and Installation
  1. Loosen the running board bolts and lower the running board to access the front fender moulding pin-type retainer.
    • To install, tighten to 23 Nm (17 lb-ft).
  1. Remove the lower pin-type retainer from the front fender moulding.
  1. Remove the 2 rear pin-type retainers from the front fender moulding.
  1. Position the front fender moulding aside and remove the splash shield lower screw.
  1. Remove the front splash shield screws.
  1. Remove the front splash shield pin-type retainers.
  1. Remove the front splash shield.
  1. Remove the front fender splash shield.
  1. To install, reverse the removal procedure.

Mar 25, 2015 | 2007 Mercury Mountaineer

1 Answer

How do you remove a fender?

Front fender? Lift the hood, open the front door on the same side as the fender to be removed. Under the rim of the hood, you'll find a line of bolts holding the top of the fender in place. Inside the door opening, you'll find one or two more bolts holding the rear of the fender in place. You may also find one bolt under the rear corner of the fender, fully underneath the vehicle. You'll also need to remove the turn signal housing, any side marker light, and possibly the headlight - all with screws - and you may still find one bolt up front, where a steel strut holds the frontmost bottom corner of the fender in place.

When you get all those fasteners removed, you pretty much just wiggle the fender off the car.

Jul 31, 2014 | 1993 Subaru Legacy

1 Answer

Drivers window fell into to door. trying to remove door panel and try to figure out what happened. don't want to damage door panel by forcing panel off. 91 cad deville 35,000 miles sitting for long time....

Had exact same problem in '91 Cad. Fleetwood FWD, which is same as '91 Deville except for trim fender skirts. My mechanic said it was a broken window regulator. That part is not available new anymore, unless you can find some NOS. I bought a used regulator from Cadillacs Only for $75, and paid my mechanic for 1.5 hours of his time to r&r. Window now works fine. Not happy that I had this problem; regulator not a great design.

Jan 15, 2011 | 1991 Cadillac DeVille

1 Answer

How do you fit side skirts to a ford escort mk6

Usually you use screws to hold it to the body, either fiberglass or urethane side skirts are all attached the same way.

Apr 01, 2010 | 1998 Ford Escort

2 Answers

Installation instructions 2005 hyundai santa fe tail light


Open rear hatch,
locate 3 philips screws on the right side of lamp,
note that the lamp assembly is held into the fender side by a plastic tab( hidden ). You have to stand at the rear fender side, facing the lamp and pull the lamp toward you carefully.

Thanks for using FixYa.
- Steve

Feb 10, 2010 | 2005 Hyundai Santa Fe

1 Answer

How to take off the right fender off a Mitsubishi 3000gt

Removeal steps
1. Remove wheel arch liner, this is a two peice part front and back. both these need to be removed, there should be 8 screws to remove.
2. You should then have access to all fender screws. There are 10 screws to remove to allow removeal of fender. 4 under the bonnet holding the top of the fender. 2 for the front going to a bracket. 1 underneath the fender where the arch liner was. 2 under the main body of the car towards the front of the side skirts and a final one, near to the door triangle where the mirror is. The fender should then come away but there is a sealant to stop water getting in, make you you reseal when putting back on with 3M ATD, part no 8625 or similar.

Dec 15, 2009 | 1997 Mitsubishi 3000GT

1 Answer

How do I remove the rear bumper from an 09 VW Passat?

you will need to remove both rear tail lights remove the screws on top and under bottom and in the fender wells there will be a lot of screws when you get done

Sep 10, 2009 | 2008 Volkswagen Passat Sedan

Not finding what you are looking for?
2005 Chrysler 300 Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides