Question about 1995 Ford Taurus

1 Answer

1995 Taurus motor mounts

Under the front end 2 bushings wore out & broke thus causing the steel frame to drop lowering the engine. Are these motor mounts? Can I replace them? Did anything else break causing this? Can I get a diagram? Please help- Charles

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

These are known as cradle bushings. the frame around engine is called the cradle. you can get mounts from ford should just replace these and be fine

Posted on Oct 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 toyota corolla rattling noise in the front end on bumps


The rattle (noticed at times under hard acceleration) is the cause of gas shock on the upper part of the engine loosing charge, in-turn causing the engine mounts extra stress and thus metal vibrating/rattling together.
The knocking (over bumps, etc. if you have noted that) is caused by worn bushings, most likely worn sway bar end links (you will see the links looking at the undercarriage, on both sides, they are a little steel "bars" with threaded ends on a 90 deg angle held by bushings e.g. example of front sway bar links ).
I noticed these noises coming on (at various times) at about ~140,000km or ~67,000mi and drove the car as it was until ~300,000km when i sold it (as is). Annoying noises.... yes... did I turn up the radio and carry on driving this car, not "fixing" anything (and I mean not a single $ spent on it aside from maintenance) and then sell the car... yes. The choice is yours.

Nov 20, 2013 | 1998 Toyota Corolla

2 Answers

Makes a funny noise when i go over a speed bump chevy 2001 mal


what sort of noise clunks&bangs could be anything from shock mounting bushes exhaust hanging mounts or suspsion bushes.it would be a good idear 2 have a mechanic put it up on a hoist 2 check it out

Sep 10, 2011 | 2001 Chevrolet Malibu

1 Answer

The rubber bushing that hold up the under carriage,(holds engine up) ripped apart and broke


if this is a lower motor mount, replace it immediately. From your discription it sounds like it is. without it the motor will pivot and lift under load and possibly dammage more parts, this is also a safety issue for yourself...

Sep 30, 2010 | 1992 Ford Taurus

1 Answer

REPLACING THE OIL PUMP


No you can jack the motor high enough to get a 2x4 between the engine mount and frame and drop the pan,,,,,,,,,,,,,,,,, take the 2 right side engine mount bolts off from the frame ,,, raise the engine high enough to get the 2x4 between the frame and engine mounts...then drop the pan out of it

Jul 15, 2010 | 1999 Ford Taurus

2 Answers

Replacing sway bar. cannot get new sway bar to propper position. how do i get it to fit propperly?


Your old sway bar made of tubular steel. New sway bar made from solid steel. You have a frame under engine the sway bar attaches too. This frame also supports your engine and trans mounts. Follow frame and there are 4 bolts securing same. Mechanic I watched supported engine underneath. Loosen back bolts though not removed. (please note sway bar has arrow that bar can only go in one direction) This maybe your problem. Attach bar to frame and fitting's. Best if you raise front end and remove both tires. Good luck

Feb 15, 2010 | 1999 Pontiac Grand Prix

1 Answer

Passenger side front motor mount on 95 ford taurus. how do i replace it? 3.8


There should be only one front mount,there is a 18mm nut on the top of your motor mount below your a/c pump,and there is a 18mm nut on the mount up inside your frame,just remove these 2 nuts(place a jack with a piece of 2x4 on it so you dont destroy your oil pan)jack up the engine enough to remove the mount only,reinstall new mount make sure you install correctly,and facing correct way,remove jack and enjoy the ride

Nov 04, 2009 | 1995 Ford Taurus

1 Answer

Need a bushing that goes under the engine frame - what is it called?


you are looking for either a motor mount or frame stabilizer mount

Oct 26, 2009 | 2000 Ford Taurus

1 Answer

Front right bushing is broken and causes a "popping" noise


call dealer with VIN number to see if your car is involved. ALso, please explain which bushing. Safety Recall 98S36 - Certain 1986 - 1995 Taurus and Sable and 1988 - 1994 Continental Vehicles - Sub-Frame Rear Plate Nut Replacement AFFECTED VEHICLES Certain 1986-1995 Taurus and Sable and 1988-1994 Continental vehicles that were originally sold or are currently registered in the following U.S. states and Canadian Provinces: U.S. States: Connecticut Delaware District of Columbia Illinois Indiana Iowa Kansas Kentucky Maine Maryland Massachusetts Michigan Minnesota Missouri Nebraska New Hampshire New Jersey New York Ohio Pennsylvania Rhode Island Vermont Virginia West Virginia Wisconsin Canadian Provinces: Manitoba New Brunswick Newfoundland Nova Scotia Ontario Prince Edward Island Quebec REASONS FOR RECALL The body mounts on the rear corners of the sub-frame that support the engine and transmission may separate. This can occur if the lower retainer plate of the mount or the retaining plate nut becomes severely corroded from long term exposure to road salts and retention of moisture in the mounts. This corrosion can weaken the retainer plate of the mount or the retaining plate nut severely enough to allow the bolt head to pull through the washer or out of the nut. Should both rear mounts separate, the rear of the sub-frame will drop and steering may suddenly become difficult. This could result in an accident. SERVICE ACTION To correct this condition, dealers will replace the attaching bolts, plate nuts and the reinforcement plates on the bottom of the sub-frame rear body mounts, on all affected vehicles. SERVICE TRACKING

Jun 03, 2009 | 1995 Ford Taurus

1 Answer

Engine mount replacement


There are two liquid filled and a trans mount. You need to found out which way the motor jumps if it jumps back to the fire wall I would change the two liquid fill. They are located looking at the engine on the pulley side left and right bolted to A-frame you can change one at a time. Unbolt one and jack motor with a floor jack and board just lift enough to drop it in and out. It's tough I know I did it before but it can be done. And do the same for the other. Trans mounted one never needs replaced. Just make sure the mounts are bad cause front wheel drive motors usally move but if its moving more than 2"-4" then replace them.

Apr 24, 2009 | 1994 Ford Taurus

Not finding what you are looking for?
1995 Ford Taurus Logo

423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...