Question about 2000 Ford Crown Victoria

1 Answer

No start no pcm responce

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Check all fuses there is a fuse for datalink connector

Posted on Oct 21, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Whats wrong with my Durango?

IF you can get to a scan tool, you should hook it up and see what it says.

Mar 16, 2014 | 2005 Dodge Durango Limited

1 Answer

Throttle is not working no responce

is it diesel, drive by wire or cable? is the pedal hard like stone and doesnt move? if its electronic then the sensor is prob bad. if its cable and hard the throttle body needs to be cleaned to free up the butterfly or plate

Feb 04, 2012 | 1997 Mercedes-Benz E-Class

1 Answer

2002jetta TDI,Engine cuts back to an idol while driving,then there is no responce at exclerator. Shut it off then restart could run for days or sometimes only minutes??????? Glow plug light flashes when...

Jeff this sounds more to me like a flat spot which is caused by a bad TPS throttle position sensor or tranny input/output sensor where the PCM looses counts and shuts the speed, and when you cycle the key it resets itself. Are there any codes?

Feb 26, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

PCM Diagnostic Code Reading of EO22 and EO1033


Oct 11, 2010 | 1992 Cadillac Eldorado

2 Answers

Have 2001 chevy 2500hd with a code 0700 bad tcm. can you tell me where it is and how much do they run.

P0700=Transmission Control System (MIL Request)
Does not mean bad TCM,=transmission control modual,
all that happen here was the computer did not like the responce it got from a sensor,and requested the check engine light be turned on.
You need to have it scanned by a shop if it reappears

Dec 25, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

Turn iginition key no responce to starter. Bought new key with chip still n o responce.

try to start it in neutral. the trans. has a safety switch that will not allow the car to start in anything, but park and neutral. sometimes the shift lever gets a little out of line with the gear indicator. also try firmly shifting into and out of park a few times. this may flip the switch. good luck

Sep 28, 2009 | 1995 Chevrolet Lumina

2 Answers

Will not pass emissions code p0401 infuficient egr flow

EGR flow is monitored by the PCM by it looking for a reaction in the FRONT O2 sensor in responce to the command given to the EGR valve. The linear electronic EGR valve sends a return signal to the PCM indicating the relative position of the step motor and hence how far open (or closed) the EGR valve is in responce to the PCM command. The PCM expects to see (within a set of given parameters) a change in the O2 sensor reading (change in exhaust gas make up) after the EGR valve is commanded open or closed. If it doesn't, or that change is not within the expected parameters, a code will be set based on the skewed data. Generally a "insufficient flow" code will be set by:

1.Faulty EGR valve (sticking, or "lying" to the PCM about the actual valve position)
2.Faulty electrical connection at the EGR valve (causing false data)
3.Clogged EGR passages
4. Bad read from the MAP, or TPS, causing the PCM to misinterpret the EGR data based on faulty operational data from the other sensors
5. (Very rarely) A marginally "slow" O2 sensor. (PCM does not "see" the change in exhaust make up quick enough and interprets that as poor EGR flow.)
I have found that normally this code means that the EGR is not opening the amount that it has been commaneded to by the PCM. Normal cure for me lately has beed to repalce the EGR valve and to clean out the passages while the valve is off. The Tech 2 is able to command the EGR open and show the commanded opening and the actual opening. When this code is present the actual and commanded do not match closely at all. Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FREE question.

Mar 29, 2009 | 1999 Saturn SL

1 Answer

No responce from accelartor after brake peddle is pressed

If check engine light is on get the codes pulled.

Jun 04, 2017 | 1996 Audi A4

1 Answer

Poor responce when first started

If lurches when going forward and requires extra throttle, but reverses okay, it due to breakage of the valve body spring. All ZF HP-series automatics have this problem. Have a qualified Jag shop (independent is okay) replace the spring with the improved unit. If you wait too long the transmission will fail completely.

Dec 24, 2008 | 2001 Jaguar XJ8

1 Answer

No throtel responce

RE:check the fuse.......glad to see my suggestion worked.......please rate this solution as fix ya..........thanks for choosing fix ya

Dec 21, 2008 | 2002 Ford Super Duty F 450

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides