Question about 1998 Mazda 626

1 Answer

1998 mazda capella.injector pulse no spark. 4 cyl

Have replaced crank sensor and computer,stumped!

Posted by on

  • sherylpuha Oct 22, 2008

    waste spark coils both fine.ihave continuity on trigger wires from coils to ecu.engine is gf-gf8p,have replaced cam pickup also.where is computer sensor fuse block?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Sherylpuha,

Have you checked the coil from where the spark comes from and the computer sensor fuse block?

Posted on Oct 18, 2008

  • 1 more comment 
  • Jean Pienaar
    Jean Pienaar Oct 25, 2008

    Sherylpuha,



    The Computer Sensor Fuse Block, is the fuse connection between the ignition and the computer sensor. If this does not help try the wiring that runs from the computer sensor to the fuse box. then follow it to the ignition where the key switching happens?

  • RODWELL NAICKER Jul 07, 2013

    i cannot understand what is a ecu fuse block

  • RODWELL NAICKER Jul 07, 2013

    this is an import eng.fitted to the vehicle.top half is the same,bottom was changed but using the same crank

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 Mazda 6 3.0L. Got a misfire Cyl. #6. Replaced spark plug & coil. Still misfire. Swapped coil and same result. #6 misfire??????????????


misfires are more often from a blocked/faulty injector rather than electronic
pull the injector and clean or replace
check for injector operation and wires

Jan 30, 2017 | Mazda Cars & Trucks

1 Answer

2001 Mitsubishi montero sport xls replaced crankshaft sensor still will not crank


Test fuel pressure at key on. Next test for spark to plugs. Use "noid" light to test for injector pulse.

Jul 03, 2016 | 2001 Mitsubishi Montero

1 Answer

So i have a 2002 mazda protege thought it was a fuel or spark issue but ive pretty much replaced everything to do with those things. when i crank it it just winds it doesnt want to start my brother is a...


Have you checked for a strong blue spark at all cylinders? Have you checked the injector circuit? Are the injectors pulsing and putting fuel into the cylinders? Have you checked compression?


All I can think of. No theft security issues, car is not immobilized by that, is it? If all else checks out, maybe the engine computer?

Dec 12, 2013 | 2002 Mazda Protege

1 Answer

2002 galant will start up fine cold and run for 20 min, after hot soak will not start, back fires through intake


Yes your 4 cyl engine uses direct spark with a coil over each spark plug.
And the computer controls the firing of the plugs and injector pulse.
The problem could be the crank or cam sensor, or the wiring harness, but in most cases the check engine light should be on and a code set.
You might want to check the computer for codes, then try the cam sensor.

Sep 22, 2012 | 2002 Mitsubishi Galant

1 Answer

Car starts and runs for about 13 to 20 minutes got new computer map mas still no go. wait for engine to cool off and will start. fan does not engage but sensors test ok. during diagnostics fan will run i ...


Just did one in my shop yesterday. MY problem was injectors shorting out drivers in PCM after half hour of cooling down it would restart and die again about 20mins later. You need to narrow down what is dropping out. Most likely your loosing injector pulse and/or spark. You can buy a noid light for injector testing and a inline spark tester which you can tag on igition coil pack from local parts store also you can tag into injector harness on passenger side of engine with noid light, when it stalls see if light is blinking while cranking on both testers. IF you have spark but no injector pulse you have one or more injectors shorting (acceptable range is 13 ohms) any lower than 13 ohms injectors are toast. IF no spark and no pulse your ignition module and or crank sensor are bad, replace both, module is under coil pack and sensor on side of block.

May 12, 2011 | 1988 Buick Regal

1 Answer

1990 gmc 6500 topkick with no spark or injector pulse. all 4 wires on the ignition coil have battery voltage with key on. is coil shorted or is the ignition module bad?


You are jumping to conclusions. Slow down.
No spark AND no injector pulse indicates none of the desired outputs were triggered. The ignition module makes spark when it receives a crankshaft position sensor signal, and then transfers control of that spark to the computer after it starts. The module takes its crank sensor signal and generates an RPM count that it forwards to the PCM(main computer) which is used for triggering the injectors and controlling timing. SO, if you had a bad crank sensor OR a bad ignition module, you could lose both spark AND fuel. a coil would not disable injector pulse. modules RARELY fail in a manner that disables RPM reference to the computer causing it to not fire the injectors...At this point, I would TEST the crank sensor as the next step. If its easier, 1 of the wires on the module goes directly there so you can test the crank sensor at the module.

Sep 18, 2009 | 1990 GMC K3500

1 Answer

Car has no spark or injector pulse(new ecm,crank sensor)


Check the fuse for the injectors, some vehicles have the injectors and coil running on the same circut, at the same time check the fuse for the ignition.

Jan 30, 2009 | 1996 Dodge Avenger

1 Answer

NO start


Make sure you are getting gas and spark, they are a few ground wires that come off of injector harness that if they are not grounded will cause injector NOT to pulse re-check wiring and get back to me. Good Luck

Dec 11, 2008 | 1989 Mazda 626

2 Answers

ABS, Traction control and handbrake light is on. Car was running on 3 cylinders previous to the lights coming on. 1999 Mazda SP20 Familia (323)


I have a Mazda Capella (626) 1998 and had similar problem other than it was running on 4 cylinders and the hand brake light was not on and the ANSWER was a speed sensor which is to do with ABS system needed replacing. You can determine which one is broken by putting volt meter over each of them.

Nov 17, 2008 | Mazda 323 Cars & Trucks

Not finding what you are looking for?
1998 Mazda 626 Logo

Related Topics:

474 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...