Question about 2006 Chevrolet HHR

1 Answer

HHR IAT sensor

Which wires in harness at air intake go to IAT sensor?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Location of ATI sensor on a 2006 HHR LT 2.4L

Posted on Nov 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix a 2005 Chevy Trailblazer code PO113


Intake Air Temperature Circuit High Input

A code P0113 may mean that one or more of the following has happened:
Internally failed IAT sensor Faulty connection at IAT sensor
Open in IAT ground circuit or signal circuit
Short to voltage in IAT signal circuit or reference circuit IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
Faulty PCM (less likely but not impossible)

Oct 20, 2015 | Cars & Trucks

1 Answer

Undefinedas replacement on civic 98 sensor p0113


Possible causes for this code are: - Faulty Intake Air Temperature (IAT) sensor
- Dirty air filter
- Intake Air Temperature (IAT) sensor harness is open or shorted
- Intake Air Temperature (IAT) sensor circuit poor electrical connection. this code sets when: - An excessively high voltage from the sensor is sent to ECM. Usual Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P0113 1998 Honda Civic Description The Intake Air Temperature (IAT) sensor is built into mass air flow sensor or in some vehicles mounted to the air filter duct housing. The sensor detects intake air temperature and transmits a signal to the Engine Control Module (ECM).The temperature sensing unit uses a thermistor which is sensitive to the change in temperature. Electrical resistance of the thermistor decreases in response to the temperature rise. The Intake Air Temperature signal is used as an input for various systems in the vehicle.
27782.png

Sep 24, 2014 | 1998 Honda Civic

1 Answer

89 dodge ram truck 2500 2wd code reader says 4 codes dont know what they mean p1509, p1298, p0118 andp0113


P1509 Dodge - Leak Detection Pump Switch or Mechanical Fault

P1298 Dodge - Air/Fuel Ratio Lean Under Wide Open Throttle Condition
- Plugged air filter
- Plugged fuel filter
- Defective fuel pump
- Ignition system weak-misfires
- Defective coil

P0118 Dodge - Engine Coolant Temperature Sensor Circuit High
- Low engine coolant level
- Faulty Engine Coolant Temperature (ECT) sensor
- Faulty engine coolant thermostat
- Engine Coolant Temperature (ECT) sensor harness is open or shorted
- Engine Coolant Temperature (ECT) sensor electrical circuit poor connection

P0113 Dodge - Intake Air Temperature Sensor 1 Circuit High
- Faulty Intake Air Temperature (IAT) sensor
- Dirty air filter
- Intake Air Temperature (IAT) sensor harness is open or shorted
- Intake Air Temperature (IAT) sensor circuit poor electrical connection

Dec 16, 2013 | Cars & Trucks

1 Answer

Honda civic codes p1361 & p0113 along with gas smell


P1361 HONDA - Top Dead Center Sensor 1 Intermittent Interruption
Possible causes- Top Dead Center Sensor 1 harness open or shorted
- Top Dead Center Sensor 1 circuit poor electrical connection
- Faulty Top Dead Center Sensor 1P0113 HONDA - Intake Air Temperature Sensor Circuit High Voltage

Possible causes- Dirty air filter
- Intake air temperature (IAT) sensor harness is open or shorted
- Intake air temperature (IAT) sensor electrical circuit poor connection
- Faulty intake air temperature sensor

Oct 17, 2012 | Honda Civic Cars & Trucks

1 Answer

2002 HYUNDA1 PO111 SENSOR 1


P0111 HYUNDAI - Intake Air Temperature Sensor 1 Circuit Range/Performance Problem.
It is very likely the sensor got disconnected during some service work like replacing the engines air filter.
Other causes- Dirty air filter
- Intake air temperature (IAT) sensor harness is open or shorted
- Intake air temperature (IAT) sensor electrical circuit poor connection
- Faulty intake air temperature sensor

Read more: http://engine-codes.com/p0111_hyundai.html#ixzz290YBI1ZJ

Oct 11, 2012 | Cars & Trucks

1 Answer

P0113 code for the intake air temperature sensor


Thank you for the inquiry.
P0113
Intake Air Temperature Circuit High Input
P0114 Intake Air Temperature Circuit
P0113 - Intake Air Temperature Circuit High Input

The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.

Potential Symptoms: There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).
Causes: A code P0113 may mean that one or more of the following has happened:
* Internally failed IAT sensor
* Faulty connection at IAT sensor
* Open in IAT ground circuit or signal circuit
* Short to voltage in IAT signal circuit or reference circuit
* IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
* Faulty PCM (less likely but not impossible)

Possible Solutions:
1. First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. 2. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground.
3. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.


Hope helps; keep us updated and remember to rate this answer

Jun 04, 2011 | Saab 9 3 Cars & Trucks

2 Answers

P0113


P0113 - Intake Air Temperature Circuit High Input

What does that mean?
The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.

Potential Symptoms
There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).

Causes
A code P0113 may mean that one or more of the following has happened:
* Internally failed IAT sensor
* Faulty connection at IAT sensor
* Open in IAT ground circuit or signal circuit
* Short to voltage in IAT signal circuit or reference circuit
* IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
* Faulty PCM (less likely but not impossible)

Possible Solutions
First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.

Hope this help (remember rated this).

Jun 10, 2010 | 1997 Chevrolet Camaro

1 Answer

2003 911 carrea has fc p0113 intake air temp sensor high out put has new air mass. sensor replace fc come back .please advisor for further diag.


A code P0113 may mean that one or more of the following has happened:
  • Internally failed IAT sensor
  • Faulty connection at IAT sensor
  • Open in IAT ground circuit or signal circuit
  • Short to voltage in IAT signal circuit or reference circuit
  • IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
  • Faulty PCM (less likely but not impossible)

Oct 30, 2009 | 2004 Porsche 911

1 Answer

2007 gmc sierra 2500 IAT sensor


Well, the IAT (Intake Air Temperature) sensor is located on the air intake duct between the filter and the throttle body (Assuming you have the 6L motor). The wires are easily visible at the plug that connects the sensor to the wiring harness. That's the easiest place to access them.

May 18, 2008 | 2004 GMC Sierra 2500

Not finding what you are looking for?
2006 Chevrolet HHR Logo

Related Topics:

594 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...