Question about 2000 Ford Windstar

1 Answer

2000 windstar left signal not work

Letf signal wont work

Posted by on

  • 1 more comment 
  • zacjim Oct 30, 2008

    Fuse for left blinker blows intermittently.
    I have replaced fuses and bulbs. They hold for a while, then blow again.

    I have had intermittent prob's with door locks as well

  • yadayada
    yadayada May 11, 2010

    Do you have trailer tow wiring?

  • Loringh
    Loringh May 11, 2010

    Is this the front or rear indicator

    does the left turn indicator on your instrument panel stay on when you turn the left turn lever on?

    If yes, then this indicates the bulb is burned out.

    Get back with me and I'll tell you how to change the bulb. It's not difficult.

    Sincerely Loringh


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

The light is bad change it

Posted on Aug 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 ford windstar brake lights, signals, reverse lights wont work. Gas gage wont work


Take it to your local FORD dealership,their probabbly the only ones who can fix that.

Nov 06, 2013 | Ford Windstar Cars & Trucks

1 Answer

2000 ford windstar wont start changed starter battery is good changed fuses all lights work


Wild guess but the car will not start if it does not get the in "Park" or "Neutral" signal from the column switch. check for that it may just be so.

Jun 15, 2010 | 2000 Ford Windstar

3 Answers

Looking for fuse box on 1998 ford windstar


Fuse panel is located behind the instrument panel to the left of the steering column. There is also a fuse panel located on the left side of the engine compartment. Fuses #25 and #27 on the interior fuse panel are both associated with the turn signals.
I hope this helps you!

Apr 10, 2010 | 1998 Ford Windstar

1 Answer

Brake light, reverse light and turn signal issues


Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Jan 28, 2010 | 2003 Ford Windstar

1 Answer

How do i change the front turn signal bulb on my 2000 windstar lx


The screw that holds the lens must be unscrewed. Then,
you can replace the signal bulb. Put the lens back in place, and it's all done.

Jan 18, 2010 | 2000 Ford Windstar

1 Answer

Left back signal not working right brake not working new bulbs no broken wires


I have seen a couple of these. If this has a tilt steering wheel,what happens is the wiring to the turn signal switch pulls out of the hard shell connector,maybe one or two wires.In your case it is the left turn signal circuit.Remove the cover around the column (3 to 4 screws) and inspect the wiring.This might be difficult to do,so you might want to take it to your local repair shop to diagnosis the problem.

Nov 12, 2009 | 2000 Ford Windstar

1 Answer

I have a 2000 windstar...the left sliding door


The door is not catching to lock the door shut. Find where it is not catching and see if theres a blockage or if something is broken.

Oct 17, 2009 | 2000 Ford Windstar

1 Answer

Turn indicator light flashes quickly. bulbs fine


The quick flash is a fault detection for a burnt out bulb. If bulb is good, check bulb socket. Inspect for corrosion. If needed, replace bulb socket. Check bulb socket connector. Check if fuse. Check emergency flashers ( most cars have a separate circuit).

Jul 09, 2009 | 2000 Ford Windstar

1 Answer

Passenger window wont roll up or down , power mirrors go left and down on both sides on 2002 ford windstar van


bad window motor ,or bad cables on window motor check for power too the moter first

Mar 03, 2009 | 2000 Ford Windstar

1 Answer

2000 ford windstar, directionals both not working, hazards work f


turn signal flasher module or turn signal switch. I usuall try to wiggle teh column switch or move it slowly up and down, back and forth to help determine if it has a bad contact. if i cant get a failure (or turn signal) that way I begin the testing at the base of the column. the flasher module is a common failure on those and isnt unreasonably priced. if i had no diagnostic procedure i would try that first. oh yea, try turning the hazards on and off rapidly several times. the signal goes through the four way switch.

Dec 31, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...