Question about 2004 Volkswagen R32

2 Answers

R32 2004 How do you remove the plug wires to change the spark plug?

Posted by on

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

First you have to unclip the plastic lid over the engine. just pull up easy there's clips holding it in. Very carefull not to brake it. Now if you have a sway bar it will be harder trying to slid the lid off. There's going to be six red plastics that run horiontal when you stand in front of the engine the look like the engicters, but they are not. That's the spark plug wires that leads you to the spark plug. Just pull out on them or unclip them which is harder to do, and you might break them. Very Very important becareful not to break the clip on plastic head of the spark plug wires.GOOD LUCK and becareful it all plastic.

Posted on Jun 19, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 88 Answers

Their is a high tension lead removal tool you can buy.if its coil per cylinder ther is a clip that you squeeze to remove the wires off the coil

Posted on Oct 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change spark plugs


  1. Disconnect the spark plug wire at each spark plug.
    • Twist each spark plug 1/2 turn.
    • Pull only on the boot in order to remove the wire from each spark plug.
  1. Disconnect the spark plug wire from the ignition coil.
    • Twist each spark plug boot 1/2 turn.
    • Pull only on the boot in order to remove the wires from the ignition coil
  • Install the spark plug wires at the ignition coil.
  • Install the spark plug wire to each spark plug.
  • Inspect the wires for proper installation:
  • Repeat above procedure for all 8 cylinders.
  • Jun 17, 2013 | 2003 Hummer H2

    Tip

    Changing spark plugs in any car


    When changing spark plugs I find it best to remove only one wire at a time. I remove the wire, change the plug, measure the old wire against the new wires, and replace the wire before moving to the next wire and plug. This way I do not have to know the firing order for the plugs.
    Don't for get to check the plug gap.

    on Dec 04, 2009 | Buick LeSabre Cars & Trucks

    1 Answer

    Describe your how fix my pontiac 2000 montana Problem changing spark plugs



    Inspection

    Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
    If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


    Removal & Installation

    3.5L Engine

    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Remove the left side spark plug wires from the spark plugs.
    3. Remove the left side plug wires from the retaining clips.
    4. Rotate the engine for access as follows:
      1. Set the parking brake.
      2. Shift the transaxle into neutral.
      3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
      4. Install the Engine Tilt Strap J-41131.
      5. Pull on the engine in order to rotate the engine forward.
      6. Tighten the strap.

    5. Remove the right side spark plug wires from the spark plugs.
    6. Remove the plug wires from the retaining clip.
    7. Remove the spark wires from the ignition coils.
    8. Remove the plug wire assembly from the engine.
      NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

    To install:
    1. Install the right side plug wires to the ignition coils and then the spark plugs.
    2. Install the spark plug wires to the retaining clip.
    3. Rotate the engine back to the original position.
    4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
    5. Install the spark plug wires to the retaining clips.

    3.9L Engine
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Remove the intake manifold cover.
    3. Remove the left side spark plug wires as follows:
      1. Disconnect the left side spark plug wires from the spark plugs.
      2. Disconnect the left side spark plug wires from the ignition coil.
      3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
      4. Remove the left side spark plug wire assembly.

    4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
      1. Set the parking brake.
      2. Shift the transaxle into neutral.
      3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
      4. Install the Engine Tilt Strap J-41131.
      5. Pull on the engine in order to rotate the engine forward.
      6. Tighten the strap.

    5. After rotating the engine, remove the right side spark plug wires as follows:
      1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

    6. Remove the right side spark plug wire clip from the ignition coil bracket.
    7. Remove the right side spark plug wire assembly.

    To install:
    1. Install the spark plug wire assembly.
    2. Install the right side spark plug wire clip at the ignition coil bracket.
    3. Connect the plug wires to the ignition coil and spark plugs.
    4. If the engine was rotated for access, return the engine to the original position.
    5. The remainder of the installation is the reverse order of removal.

    Feb 05, 2011 | 2000 Pontiac Montana

    2 Answers

    My spark plugs in my 2004 Mitsubishi Endeavor needs to be changed, and my husband wants to do it himself so is there some way to give me some instructions on how to change spark plugs for my 2004...


    YOU NEED LONG SPARK PLUG SOCKET. NEED A 3/8 INCH RATCHET WRENCH.YOU NEED EXTENSION.YOU NEED SPARK GAUGE YOU NEED A TORQUE WRENCH. NOT MANDATORY JUST DONT OVER TIGHTEN SPARK PLUGS STRIP ALUMINUM THREADS WAIT UNTIL ENGINE COOL TO KEEP FROM WARPING THE HEADS. SPARK PLUGS LOCATION ON TOP OF CYLINDER HEADS.TO GET TO SPARK PLUGS THE COILS ON TOP EACH SPARK PLUG.HAS TO BE REMOVED BY REMOVING SMALL SCREW.THAT HOLD COILS DOWN.AND CHANGE ONE SPARK PLUG AT A TIME SO YOU WONT GET THEM MIXED UP.GAP PLUGS AT 0.028 - 0.031

    Jan 28, 2011 | Mitsubishi Endeavor Cars & Trucks

    1 Answer

    My 96 bronco 5.8 stumbles on acceleration.


    Did it spark well on all the plugs? Usually if you have no change in idle with two wires removed it needs a new set of spark plug wires. If it was cylinder 2 & 3 (side by side) then you should suspect a head gasket. Does the Bronco have multiple coils or a coil pack with multiple inputs? Are these two plugs hooked up to one coil?

    Feb 11, 2010 | 1996 Ford Bronco

    2 Answers

    How do i change spark plugs


    get your tools out and learn on the job

    Jan 23, 2010 | Daewoo Nubira Cars & Trucks

    2 Answers

    How do I change Spark plugs?


    93 park ave has a v8. Four plugs on each side. Followthe spark plugs from top of engine to spark plugs. Use a spark plug wire remover (plastic pliers) to help remove wire from plug. Mark each wire where they go. Go down to auto store and buy pugs and get a swivel spark plug wrench to fit the plugs anduse a extension with rachet to remove plugs (turn counter-clockwise to remove). Replace with new. (new plugs should screw in with fingers, then tighen with socket firmly. Not over tight. I holp this helps a little - ran out of writing space. Good luck

    Oct 15, 2009 | 1993 Buick Park Avenue

    1 Answer

    CHANGE SPARK PLUGS 2004 GMC ENVOY


    Well first you will want to get the right size spark plug socket , the rigt sized one for your envoy and then next you will want to remove one spark plug wire at a time so you do not cross any of the wires or if you do you will mess up the timing for the envoy now how to remove a spark plug wire, look first at the plug wire and then gentky twist the wire on the end that goes over the spark plug and carefuly pull back but do not break the wire, next with an extention and the socket put the socket over the spark plug and turn the plug counter clock wise until you have removed the plug and then put the new spark plug in and place the spark plug wire back on the spark plug and just repeat the prosses on the rest,agin do them one at a time that is how I change spark plugs and wires and i have been doing it for years.

    Sep 15, 2009 | 2004 GMC Envoy

    2 Answers

    Changing spark plugs on lincoln town car


    Remove the spark plug wires, remove the spark plugs,replace them. Do this one cylinder at a time if you never did it. On that year you may need to remove the upper intake to access the plugs on one side. In that case go to a shop. This would not be a novice job.

    Jun 28, 2009 | 1998 Lincoln Town Car

    1 Answer

    Change spark plug wires on 04 kia sedona


    REMOVAL OF THE PLUGS:

    Do not attempt any maintenance on spark plug if engine is hot. 
    1. Disconnect negative battery terminal. 
    2. Carefully remove high-tension leads. 
    3. Use compressed air to blow any dirt or debris from around spark plug hole. 
    4. Check that spark plug fits squarely in spark plug socket and remove spark plug.

    Raise a vehicle and install SST(OK552 131 001) in order to replace cylinder 2, 4, 6 spark plug. 

    INSTALLATION:

    1. Install spark plug into cylinder head.

    Tightening torque : 18~22lb-ft (25~30N·m, 2.5~3.0kg-m)

    2. Reconnect high-tension leads. 
    3. Reconnect negative battery cable. 

    Hope this helps and simple to understand. Good luck

    Apr 20, 2009 | 2004 Kia Sedona

    Not finding what you are looking for?
    2004 Volkswagen R32 Logo

    Related Topics:

    227 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volkswagen Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    60867 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Volkswagen Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...