Question about 1987 Plymouth Voyager
Ok i have a problem, my van wil turn over but won't stay running,it starts then dies immediately. i have changed the iginition switch and wiggled every wire i could get ahold of.i left it alone monday night and it ran for about 1/2 hour. drove it home tuesday night,no problem,got in it this morning,started ok ran to store about 10 minutes,would not restart. any ideas? thanks for any help you can offer.
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Hi Wayne, what you do is turn the key to the "on" position and back to "off". Do this three times. The engine light will flash. It will flash a certain amount of times, pause, then another set of flashes. The first set of flashes is the first number of your code. The second set is the second number. For example, you see 5 flashes, your first number of your code is 5, and so on.
Posted on Jun 11, 2008
What is it a Start Relay in Auto, 95 Plymouth Acclaim?
(1) On September 11, 2008 at 5:07 pm Miguel A. San Antonio  said:
1. 1995 Plymouth Acclaim Sedan, 4 cylinders. 2.5 litter Repair Fuel Pump Steps or Procedure?
Replace the Fuel Pump and still not start.
2. What I need to do to remove the Fuel Pump and put the new one in?
Remove the ground cable or negative cable of the Battery.
There is not was pressure inside the gas tank, maybe because the fuel pump issue.
Was not easy repair job, to remove the filler neck of the gas tank. I have to disconnected first of the outside to be able to jiggle the filler neck to disconnect of the gas tank.
And I think was the start relay issue. I just bought the start relay and I will find out when I get home. When I should installed the start relay, will find if it was the Start Relay.
As follow ;
Please, sent the answer as soon you can to my e-mail address, as follow; firstname.lastname@example.org
Miguel A. San Antonio
Posted on Sep 15, 2008
1- under the hood their is a two relays Fuel pump and engine cut off. locate both relays. Next time the vehicle will not start have someone inside the vehicle turn the key to start and if feel with your fingers the top of the relay and listen for the CLICK. It is possible that one of the relays is sticky. I would just replacement as they are only 10-12 bucks from most dealers and auto parts stores. If this does corrected the problem next time the vehicle does not start bang the gas tank with a sometime and try it again. If it starts after banging then you fuel pump motor is sticking
Posted on Nov 22, 2008
cracked fuel line sucking air bubbles? i have the same problem right now with my 85 ram and am about to replace the rubber lines out of desparation.
Posted on Nov 22, 2008
Hello, I would assume this is your fuel pump inside your tank. I would first however do some basics like a general tuneup. For starters I would replace your spark plugs and wires, rotary cap and button and check your fuses. Run some injector cleaner through your system. You know quick simple cheap things before you get to the fuel pump inside the gas tank which can be kinda expensive. The warm up then dies can be caused by, "blownout or fouled," spark plugs. I hope this gives you a general direction in which to go. A sidenote is that coil packs do not normally run an igntion code and I for one do not like them becuase they are expensive.
Posted on May 20, 2009
Tips for a great answer:
Jan 30, 2014 | Nissan Cars & Trucks
Feb 20, 2013 | Toyota 4Runner Cars & Trucks
Feb 19, 2013 | Cars & Trucks
Dec 06, 2012 | 2002 Ford Escort
Aug 17, 2012 | Cars & Trucks
May 13, 2017 | 1999 Pontiac Montana
Jul 28, 2011 | 1995 Pontiac Firebird
Mar 02, 2017 | 1998 GMC Savana
Apr 10, 2010 | 1988 Chevrolet G20
Jan 31, 2009 | 2001 Chevrolet Tahoe
Feb 13, 2018 | 1987 Plymouth Voyager
64 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: