Question about Audi A4

2 Answers

Misfiring /not firing on all cylinders - A4 Audi Cars & Trucks

Posted by on

  • andiotis Apr 09, 2009

    my car is misfiring/ not firing and it sputtering when i attempt to accelerate. I have had the coils and plugs changed. It ran ok for a few hours and the check engine light is now back on and occasionaly bliks at me.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

Most common thing would be to check plugs and wires. may just need a tune up. look at wires and see if you see one rubbed thru

Posted on Oct 15, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

305 CHEVY ENGINE 6 & 7 CYL NOT FIRING

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Miss fire cylinder 4 1998 chevy metro lsi


check the injector for that cylinder as the electrics is not the only thing to cause a misfire.. Put the injector in another cylinder and see if the misfire has moved

Mar 01, 2014 | 1998 Chevrolet Metro

1 Answer

Number 3 and 4 are not firing from coil on 2002 subaru outback 2.5


its faulty coil.

Get the compression test done on each coil.these will let you know if its faulty coil or not.

=========

It can be issue with spark plugs or faulty spark plugs. Also get the compression test done for cylinders. If any of cylinder shows low compression then required, then that particular cylinder will cause misfire.

Also get obd codes scanned, the error code will let you know which cylinder is misfiring or all cylinders are misfiring.

-----------

For your trouble shooting I suggest you to refer the help oinks below. It has step by step details for many engine misfire issues.

----------


Click the link below:-----


Ford Explorer Cylinder Misfire?

http://whoisbyme.blogspot.in/2012/06/ford-explorer-cylinder-misfire.html

---------

Engine Misfire codes on Chevrolet Malibu?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html

---------

Cylinder 6 Misfire?

http://howtobyme.blogspot.com/2011/12/cylinder-6-misfire.html

------------

Misfire on cylinder 4?

http://schematicsdiagram.blogspot.com/2011/12/misfire-on-cylinder-4.html

-----

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

----------

Ford Explorer 5.0L: Engine Miss?

http://whoisbyme.blogspot.in/2012/06/ford-explorer-50l-engine-miss.html

-----------

Oil on spark plugs and car misfires?

http://technoanswers.blogspot.in/2012/02/oil-on-spark-plugs-and-car-misfires.html

------------

Can cylinder misfire Damage the Catalytic converter?

http://schematicsdiagram.blogspot.in/2012/02/can-cylinder-misfire-damage-catalytic.html

------------

Car misfires and error code P0306 and P0303 is shown?

http://technoanswers.blogspot.com/2012/01/car-misfires-and-error-code-p0306-and.html

-----------

Chevrolet K1500 No spark, random misfire

http://repairhelpcenter.blogspot.com/2012/11/chevrolet-k1500-no-sparkrandom-misfire.html

-------------

2004 Ford F150: Engine Misfire and Lean Code?

http://whatisbyme.blogspot.in/2012/05/2004-ford-f150-engine-misfire-and-lean.html

-----------

1995 Toyota LS: Misfire at idle or low RPM

http://whatisbyme.blogspot.in/2012/04/1995-toyota-ls-misfire-at-idle-or-low.html

--------------

Toyota Corolla: Random Misfire?

http://technoanswers.blogspot.in/2012/04/toyota-corolla-random-misfire.html

----------

2006 Ford Freestar: Misfire on Cylinder Number 2?

http://whatisbyme.blogspot.in/2012/06/2006-ford-freestar-misfire-on-cylinder.html

-----------------------------


This will help.

Thanks.

Nov 28, 2012 | Cars & Trucks

2 Answers

What do I need done if codes p0171 p0174 p0301 p0305 p0316 is it major problems


OK, We'll cover the Diagnostic Test Codes (DTCs), starting with the standard definition set by SAE J2012 (Revised December 2007)
DTC P0171 "System Too Lean Bank 1"
DTC P0174 "System Too Lean Bank 2"
DTC P0301 "Cylinder 1 Misfire Detected"
DTC P0305 "Cylinder 5 Misfire Detected"
DTC P0316 "Engine Misfire Detected on Startup (First 1000 Revolutions)"

The "system lean" codes are pretty much telling you that there is way too much oxygen in the exhaust. There is too much oxygen on BOTH sides of the engine, and that is why you are getting codes for bank 1 and for bank 2. Bank 1 is the side where #1 cykinder is located and Bank 2 is the opposite side.

The misfire codes are pretty self-explanatory. #1 and # 5 cylinders are misfiring. The P0316 DTC is telling you that the misfire monitor is detecting a misfire as soon as the engine starts. This tells you that it is a very severe misfire and that the engine does not have to warm up and the car does not have to be driven to detect the misfire.

A misfire can be caused by many things it can be vacuum leaks, bad spark plugs, bad ignition cables, faulty ignition coils, fouled or malfunctioning injectors or injector circuits, blown head gasket, cracked cylinder head, burnt valves, etc.. etc..

However, look at the codes you have. Then look at the firing order for your engine. 2002 Mercury Sable is only equipped with a 3.0L 2V 6-cylinder engine.
The firing order is 1-4-2-5-3-6

Now if you take the firing order and split it in half, stack the two halves on top of each other, it looks like this:
1-4-2
5-3-6

When you look at the firing order this way, you can see that cylinders 1 an 5, 4 and 3, and 2 and 6, are "PAIRED" cylinders. They are exacly opposite in the firing order. Now, the cylinder only fires every second revolution of the crankshaft. With paired cylinders, one of the cylinders in the pair will fire on the first revolution and the other cylinder will fire on the second revolution.

Looking back at your codes, please note that the cylinders that are setting the misfire codes are paired cylinders.

Now the coil pack for your ignition is actually made up of three coils. Each coil fires a set of paired cylinders. If you look at the top of the coil, it will usually be marked with the cylinder numbers that each coil tower is supposed to connect to. The coil will look just like the firing order split and stacked as above.

With all of this said, I would say that it is VERY LIKELY that your misfire codes are being caused by a defective ignition coil.

The lean codes are a little different.

These are USUALLY caused by vacuum leaks which allow too much air into the engine that is not getting measured by the Mass Airflow (MAF) sensor and causes the engine to be getting too much air and not enough fuel (running lean).

I would take a good look at all of the vacuum hoses and lines. Ford is notorious for getting holes in the rubber parts that connect the PCV tubes.

If you do not find any obvious reasons for a vacuum leak, then you may want to fix the misfire codes, reset the computer memory, and drive the vehicle to see if the lean codes come back again. The misfires COULD be the cause of the lean codes. In a perfect world, this is not supposed to happen because the misfire monitors setting codes will not allow the oxygen sensor monitors to run and set lean codes. However, I HAVE seen cylinder misfires that have caused lean codes.

I hope this helps you to figure it out. Good luck!

Feb 03, 2012 | 2002 Mercury Sable

1 Answer

I have a sebring 2004 v6 2.7 which is misfiring. put it a new coil and changed plug on cylinder that doesnt fire still no spark. im getting power all th way to the plug tested with volt meter.it reads 14...


Invalid test. When plug fires, the wire shoots around 40,000volts. When not firing, there is no current in the wire.
Try switching the misfiring plug wire with another that is firing. Switch them both at the plug and at the coil tower. If that was a bad plug wire, the misfire will now be on the cylinder where you put the suspect wire. This will confirm a bad plugwire.
Good luck.

Nov 25, 2011 | 2004 Chrysler Sebring

1 Answer

When my car is ran on computer is has cose PO300 PD. What does this indicate?


DTC P0300 - Random/Multiple Cylinder Misfire Detected
Basically this means that the the car's computer has detected that not all of the engine's cylinders are firing properly.

A P0300 diagnostic code indicates a random or multiple misfire. If the last digit is a number other than zero, it corresponds to the cylinder number that is misfiring. A P0302 code, for example, would tell you cylinder number two is misfiring. Unfortunately, a P0300 doesn't tell you specifically which cylinder(s) is/are mis-firing, nor why.

Hope this helps.

Oct 03, 2011 | 2004 Chevrolet Malibu

1 Answer

Missing,viborating


Misfire could be a number of things:
a) spark plugs - change them if used over 15K miles - inspect/regap.
b) spark plug wires - change them if over 15K miles - inspect
c) ECM (electronic control module) - test with HEI (high energy ignition) tester.

The vibrating tells me that the engine is running on less than its normal compliment of cylinders - the shaking is produced by the imbalance caused in the engine by one (or more) cylinder(s)
not firing at all.

The "Check Engine" light probably is coming on due the the misfire condition. Go to Pep Boys or
Advance Auto Pats, where they'll tell you (free) your codes causing the "Check Engine' light to be
lit - the code coming from your truck's computer will probably be one or more of:
P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel

Jun 23, 2011 | 2009 Ford F-150

1 Answer

Vehicle missing,shaking,engine light comes on


Misfire could be a number of things:
a) spark plugs - change them if used over 15K miles - inspect/regap.
b) spark plug wires - change them if over 15K miles - inspect
c) ECM (electronic control module) - test with HEI (high energy ignition) tester.

The shaking tells me that the engine is running on less than its normal compliment of cylinders - the shaking is produced by the imbalance caused in the engine by one (or more) cylinder(s)
not firing at all.

The "Check Engine" light probably is coming on due the the misfire condition. Go to Pep Boys or
Advance Auto Pats, where they'll tell you (free) your codes causing the "Check Engine' light to be
lit - the code coming from your truck's computer will probably be one or more of:
P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel

Jun 23, 2011 | 2004 Ford F150

1 Answer

What is a cylinder 3 misfire


CYLINDER 3 MISFIRING. MEANS NOT FIRING .CYLINDER 3 IS MISSING FIRE.COULD BE FAULTY OR DIRTY FUEL INJECTOR.YOU COULD HAVE BAD SPARK PLUG OR COIL AND WIRE.CLEAN FUEL INJECTORS CHANGE PLUGS AND COIL TO NUMBER 3 CYLINDER .WHEN YOU DO A LITTLE TUNE UP.THAT WAY YOU WILL KNOW IF YOU HAVE A MECHANICAL PROBLEM TO 3 CYLINDER LIKE LOW COMPRESSION.LEAKING INTAKE AT 3 CYLINDER OR BURNED OUT VALVE.

Feb 20, 2011 | 2000 Saturn SL

2 Answers

What does it mean when my car was hooked up to a computer and it said cylinder 1 misfire. My car is a 2003 Mazda 6


The cylinder 1 has a misfire- means that either the spark plug is not firing, or a fuel injector is not firing causing a no burn of hydrocarbons, or no gas in the cylinder, and therefore no power off of that cylinder.

Aug 20, 2010 | Mazda MAZDA6 Cars & Trucks

1 Answer

1995 mitsubshi lancer 1.3 hardly firing on no 3 & 4 cylinders at low revs.Seems to fire better at high revs.110k on clock.


Have you tried moving the spark plug and/or lead to another cylinder to see if the misfire moves? If it doesn't change, i.e. No. 3 cylinder still misfires i'd carry out a compression or cylinder leak test.

Sep 11, 2008 | Mitsubishi Lancer Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...