Question about Mazda B2600

1 Answer

1991 B2600 D/CAB 4X4


Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 231 Answers

Check your power steering fluid level
check the power steering belt tension
check the hosesto see if they are restricting the flow of power steering fluid
try bleeding the systek to see if there is any air in the system
try changing the power steering fluid as it may not be the rite fluid for your car
perhaps you have a defective power steering pump or the seals in it are going

Posted on Oct 15, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why is my power steering hard to turn right in the morning during cold days

Sounds like combination of steering box ready to fail along with fluid change in power steering due.

Jan 21, 2016 | 2001 Dodge Grand Caravan

1 Answer

How to pull right rotor off a B2600 mazda 4x4

Questions, Troubleshooting Help & Support Page 4 - Fixya
I have a 1996 Ford Explorer 5 speed six cylinder 4 wheel drive feels like when I put on a gas is losing powers ... How to pull right rotor off a B2600 mazda 4x4.

Rebuilding Mazda B2600I 4x4 pickup - YouTube

Dec 25, 2015 | Mazda Cars & Trucks

1 Answer

1989 mercedes 560 sel, gas, w126/ Car cold starts every morning and idles for 10 min. then stalls

the idle control motor probly worn-on the throttlbody--also the tps sensor - get intake area inspectd--a haynes manual will xplain complete car-partstore hazit--------starter fluid is used for low compression or weak spark

Dec 25, 2013 | Cars & Trucks

1 Answer

How to change front brake pads on a 91 mazda b2600

how to change disk break pads on 92 mazda bravo 4x4

Dec 04, 2011 | 1988 Mazda B2600 Cab Plus

1 Answer

I have a 2001 F350 diesel 7.3L crew cab. Since the cold night, I’ve been using my plug-in heater at. In the mornings it starts fine. But after 8hours of work (where I can’t plug the heater in), I have to...

very normal with a 7.3 to be hard starting at lower temps the only thing i can recommend is getting a remote start with cold start where it starts it every 2 hours and runs it for 10 mins other than that you need to plug it in

Dec 14, 2010 | 2001 Ford F350 Super Duty SuperCab

1 Answer

Power steering fails, light comes on at times after a cold start

The rack and pinion unit is failing. The internal seals are leaking. This is somewhat common in the Accords. A local alignment shop can repair this.

Mar 28, 2010 | 1991 Honda Accord

1 Answer

Chevy s10 pickup 1995 4cyl stantard 2wd

power loss therse days could be electrical, could be needing to take in more cold air, check the air intakes

Jun 05, 2009 | 2005 Nissan Altima

1 Answer

Hand brake adjustment on 1994 b2600 4x4 its loose and does not work at all

first thing to do is to take a look at the rear brakes and make sure there in good working order and adjusted properly.
then there is an adjustment in the cable ware the 2 cables from the rear brakes meet the cable coming from the cab

May 16, 2009 | 1988 Mazda B2600 Cab Plus

1 Answer

Horn does not work.

It could be the contacts in the steering wheel, or it could be the horn relay.

Jan 03, 2009 | 1991 Honda Accord

1 Answer

Mazda B2600

Under the dash is a brake light switch at the upper part of the pedal. This switch turns the brake lights on and off. As for the brakes not working, check you master cylinder and booster. It may need to be replace. These parts send the fluid to each wheel. If it's bad, the pedal is extremely mushy or not have pressure at all. Also check for wetness behind each wheel. You may have a fluid leak causing the same issue.

Jun 10, 2008 | 1988 Mazda B2600 Cab Plus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

270 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

71231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7001 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides