Question about 1999 Hyundai Sonata

1 Answer

Wheel bearing i have a 1999 hyundai sontata and when i exerlater the gas the wheel on the passenger side shakes, could it be the cv joint or bearing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

More likely the c/v shaft. could also be a thrown belt in the tire,or bent rim.

Posted on Nov 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Noise comming from the front passenger side wheel sounds like a flat tire but its not it gets louder as I accelerate 2000 saturn sl2


Sounds like either a wheel bearing issue or cv joint depending on the type of noise. Drive it, then jack it up, check the cv boot, do a shake down on the wheel and feel the hub to see if its hot. hot hib means bad bearing. If you see a torn boot, probably a bad cv, if you have lots of play in all axies, then prob a bearing issue.

Jun 16, 2014 | Cars & Trucks

1 Answer

Grinding sound when turning lefted and stops when breaks applied


This could be one of two issues:
First, and most likely, would be the passenger side CV shaft (outer joint).
The other possibility could be the passenger side wheel bearing.

Dec 03, 2013 | 1999 Chevrolet Cavalier

1 Answer

My 2011 hyundai accent shakes after 70 miles an hour shaking why?


Most likely a bad tire.... Start there, could also be loose lug nuts, a wheel bearing/CV Joint or an alignment but most likely a tire. Look for a bulge on the inside or outside of the tire. Jack the car and spin the tires and feel/look for a bulge. Look at the tire wear pattern and make sure it is even from side to side. Could also need balanced.

Jun 20, 2012 | Hyundai Accent Cars & Trucks

3 Answers

When I am driving and get to about 30 MPH the whole front end of my car begins to shake. The dash board and, steering wheel. It will becomes less noticable when I get to 55 MPH. And now when I slow down...


Hello, There are a lot of moving parts in the front end. You may have a bad CV joint which is on the shaft that turns the front wheels. Each side has a similar part. There are also hub bearings which are in the hub and the hub is turned by the CV joint shaft.

The CV joint can break without tearing the rubber cover on the shaft, but if someone looks under the car at the CV shaft and sees oil or grease or a torn rubber cover on the right side CV shaft; it will confirm the diagnosis.

Once this part breaks the car will not move anymore. A broken CV joint can cause other parts to fail like the hub bearings. You can call around and price the repair or if you know someone who can do the work, price the parts.

If the shaft needs to be removed, it is behind several parts which will need to be removed first.

Aug 10, 2011 | 2001 Ford Focus

1 Answer

Just installed new rotors,brake pads, bearings and tie rods to front of 2000 montana. have a whopping sound when driving , this goes away when wheels turned slightly right. when turning right corner hear a...


One of your CV joints are bad, inspect which CV joint needs to be replaced. Roll your windows down and make tight right and left corners in an empty parking lot slowly and listen for the clicking noise. If it's coming from the passenger side window or the drivers side window, which ever side the noise is coming from is the side that the CV joint has failed and will need to be replaced.
Thank you for using FIxya and replacing the front wheel bearing improperly buy hammering the CV joint out instead of using a wheel bearing puller will cause damage to the CV joint as to what you have described. Good luck and keep us posted.

Jul 20, 2010 | 2000 Pontiac Montana

1 Answer

Car shaking and pop nosie from passenger side wheel


Why drive side bearing could be a bad other.balance yes, tie rod could be bad.

Mar 16, 2017 | 1996 Ford Windstar

2 Answers

Passenger front shaking


it could be your ball joints

Dec 16, 2009 | 2000 Mercury Cougar

Not finding what you are looking for?
1999 Hyundai Sonata Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...