Question about 1999 Oldsmobile Intrigue

1 Answer

Ring gear pin maybe

Ring gear pin rear axle will it interchange w/ olds 88 99'?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 91 Answers

No ring gear pin on the rear axle. Front wheel drive. 4t65e transmission. Shared with lots of GM fwds

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

How2 change rear axle bearings and oil seal 3rd Gen Camaro


You must remove the rear cover of the differential and then remove the bolt that pins in the center pin that the pinion gears are mounted on, then push the axles inward and remove the "C" shaped clips that retain the axles in the gear carrier. The axle bearings are pressed into the axle tubes and you need a special tool to remove them, this goes for the axle grease seal as well. You will need to buy this tool kit on line or locally for more money.. Go to this LINK

Jun 12, 2012 | Chevrolet Camaro Cars & Trucks

2 Answers

How do i remove my rear axles on my 1977 dodge aspen


Top of Form 1
Raise the vehicle and remove the rear wheels.
Clean all dirt from the housing cover and remove the housing cover to drain the lubricant.
Remove the brake drum.
Rotate the differential case until the differential pinion shaft lockscrew can be removed. Remove the lockscrew and pinion shaft.
Push the axle shafts toward the center of the vehicle and remove the C-locks from the grooves on the axle shafts.
Pull the axle shafts from the housing, being careful not to damage the bearing which remains in the housing.
Inspect the axle shaft bearings and replace any doubtful parts. Whenever the axle shaft is replaced, the bearings should also be replaced.
Remove the axle shaft seal from the bore in the housing, using the button end of the axle shaft.
Remove the axle shaft bearing from the housing. Do not reuse the bearing or the seal.
Check the bearing shoulder in the axle housing for imperfections. These should be corrected with a file or polish.

Apr 24, 2011 | Dodge Diplomat Cars & Trucks

1 Answer

How to change rear wheel bearing on 2003 ford explorer 4x4


Remove all the bolts on rear differential except the 2 on the sides. Loosen the 2 remaining bolts 1/2 way and pry cover loose to drain gear grease, about 3 quarts. Once the cover is off , you will see the ring gear, and 2 small gears. The axle shaft is located insde those gears, but this is the tricky part.There is a silver pin, A little larger than your thumb,{you may have to turn
the ring gear to see] that goes from the top of the carrier through to the bottom[about 6 inches long].. There is a small bolt on one end[5/16 head] that needs to be removed before the silver pin will slide out.. Be careful not to turn axle or carrier once the pin is removed or you will turn gears out of the housing.As long as the pin is in you will be OK.Once the pin is
all the way out, push axle in to the center and "C" keeper will fall off. then carefully slide axle out. The "C" keeper holds the axle out and the silver pin keeps the axle in position. Push the axle ,after repair, all the way in and reinstall the "C" keeper,then just push axle back to reinstall silver pin

Mar 02, 2011 | 2003 Ford Explorer

1 Answer

How do I get the rear axle seal out of a 1996 4 wheel drive explorer


There is a clip on the end of the axle. Here are the steps to remove clip.1 remove inspection cover and drain.2 identify large pin separating side gears in the carrier( the carrier is the thing the ring gear is bolted too). 3 Rotate carrier till you can see small bolt holding pin in carrier and remove bolt and pin. 4 push in on axle and clip should fall off , pull axle out when clip is off. Reverse steps to install.

Feb 01, 2011 | 1996 Ford Explorer

1 Answer

HOW TO REMOVE LEFT REAR AXLE ON 1999 SUBURBAN 1500 TO INSTALL GOOD ONE


Put rear tire's on jack stand's, remove left rear tire, brake caliper and bracket and slide off brake rotor, then remove rear end cover get a pan for fluid to drain into,there will be a set of gear's through the gear's on the right side of the ring gear there will be a pin about 13/4" in dim. and about 5" long at one of the end's there will be a small bolt that hold's that pin with an 8mm head going through it, remove that bolt,slide pin out, go over to axle push in (do not turn axle) go back under truck remove horse shoes clip at end of axle, then side axle out, install new axle and refill with gear oil some take a anti-slip additive.Goodluck

Dec 04, 2009 | 1999 Chevrolet Suburban

1 Answer

Rear axle oil seals leaking, book shows to remove pinion shaft lock bolt so as to remove pinion shaft, but i find no bolt to remove, is this shaft press fit or did they foget to install bolt?


TAKE TIRES OFF, REMOVE DIFF. COVER, ON 3rd MEMBER THERE A PIN ABOUT 11/2" DIA. THAT GOSE RIGHT THOUGH THE 3rd MEMBER CLOSE TO ONE OF THE ENDS OF THAT PIN OPOSIT OF RING GEAR THERES AN 8mm SMALL HEAD BOLT ( TURN RING GEAR TO CHECK OTHER END OF PIN ) REMOVE BOLT PUSH AXLE IN REMOVE HORSE SHOES CLIP IN 3rd MEMBER SLIDE AXLE OUT.

Nov 10, 2009 | 2003 Chevrolet Silverado 2500HD

2 Answers

How do you change rear axle seal in a chevy pickup


To change the rear seal, yo will need to raise and support the rear of the vehicle. Remove the wheels and drums or rotors (depending on drum or disc brakes.) Remove the rear differential cover bolts and the cover (have a drain pan under the differential) You will likely need to turn the driveshaft so the center pin bolt is acessible at the back or the differential. This is a 5/16" (or 8mm) bolt that is on the right (passenger) side of the differential carrier assembly. I recommend a new bolt be installed here on reassembly. Once the retaining bolt is out, slide the center pin out enough to allow the axle shafts to be pushed in toward the center of the diff. to remove the "C" clips that retain the axle shafts in the carrier assembly. Be careful if you happen to pull the center pin all the way out not to allow the carrier assembly (has the ring gear mounted on it) to turn, as this can rotate the spider gears out of alignment causing a headache on reassembly. With the "C" clip removed the axle shaft can be pulled out of the diff. Inspect the bearing area of the shaft for rust, pitting, or scoring. Remove the old seal and carefully install the new one. Reverse proceedures to install. Take care to note the "C" clips and center pin bolt are properly reinstalled. Fill with 2.5 to 3 quarts of rear axle grease for you vehicle.
good luck.

Oct 25, 2009 | 2000 Chevrolet Silverado

2 Answers

Part names


cardan centering bearing
point bolts needed to be removed that connects D.S.to transfercase

May 22, 2009 | 2001 Ford Excursion

1 Answer

I need to remove my rear axle shaft


These rear ends don't use c-clips on the axle shafts to remove the axles.

It must be done by removing the axle at the backing plate area.

May 19, 2009 | 1997 Nissan Pickup

Not finding what you are looking for?
1999 Oldsmobile Intrigue Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...