Question about 1989 Subaru Justy

3 Answers

89 justy wont start-no spark.

I had the cjutch replaced and now no spark. The mech. went all through the elecs. and couldn't find prob. I have a light flashing inside the ECU,(L.E.D.) three times quickly. The big prob is no spark at coil, do the flashes mean anything? I am a motorcycle mech. and have a bit of knowledge, but I hate changing part after part until prob is fixed. Is it ECU, or breakerless trigger, or............ HELP please!!!

Posted by on

  • Hay-MAN Oct 17, 2008

    I don't believe this car has one, it uses the trigger in the distributor as that sensor. I think that may be the prob though.

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have fire from coil but no fire to plugs ,,i also put on new distribtor still no fire to plugs

Posted on Jul 17, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

  • Expert
  • 52 Answers

The flashing usually refers to an error code. long and short flashes translate into a number, then you look it up.

long flash = 10's digit
short flash = 1's digit

long long long short = 31

email me if you want and i'll look up the code for you.

Posted on Nov 04, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Doesnt the crank sensor use the flywheel for its signal maybe the sensor got damaged during the clutch job

Posted on Oct 15, 2008

  • Randy Harkins
    Randy Harkins Oct 17, 2008

    I hate to say it but check for pinched or knocked off wire from when the clutch got replaced Is there 12V on the + side of the coil? Is there a blinking test light on the - side of the coil? if so and no out put the coil is bad and we can stop looking for a trigger problem.



    You do have 12v going into the distributor key on right?

    Can I call u? or you call me 253-691-6206

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parking lights flash


no help has to be checked out by elec person

Dec 03, 2017 | 2001 Dodge Caravan

1 Answer

Random blinking of lights on dashboard, then battery out


Could be a weak or failing alternator. Have it tested.

Jul 15, 2013 | 2006 Hyundai Sonata 2.4

1 Answer

Two months ago I went through the car wash and my ebrake and battery lights started flashing intermittently heater blower losses strength when I accelerate and the headlights dim. Started idling crappy at...


it sounds like you have a bad ground. follow all your ground wires. should be one to the engine, body, and maybe frame. disconnect them and clean the surfaces with sand paper and reconnect

Jan 20, 2013 | Cars & Trucks

1 Answer

I cannot open the fueal tank and I lost the users' manual; also I have to leave and tank....


is it mechanical or elctrical, if mech. try to release the arm and make it free.
and if elec. ,from inside make sure of wire connection of fuel tank cover lock.

Apr 28, 2011 | 1997 Audi A4

1 Answer

1984 FIERO 4 CYL STICK. had a aftermarket elec temp gauge mounted on console, replaced with a mech temp gauge. after replacing temp gauge is when the fuel gauge messed up. now when you turn on the key or...


I assume you replaced the temperature sending unit when you installed the aftermarket gauge? You need to put the proper sending unit back in for the OEM gauge to work.

You can find a sending unit here (and a gauge if needed):

http://www.fierostore.com/

Hope this helps

Nov 06, 2010 | 1984 Pontiac Fiero

1 Answer

Mech or Elec overdrive


According to Haynes Auto Repair Manual, section on automatic transmissions, the 1994 Towncar has the AODE transmission
Baumann Electronic Controls website
URL: http://www.becontrols.com/tech/ch1alphabet.htm
has following:
The Automatic Overdrive (AOD) transmission was introduced in 1980 as Ford's first four-speed automatic overdrive transmission.
The AOD-E transmission is essentially a beefed-up electronically-controlled version of the AOD.
If this doesn't answer your question, you might troll around the website.

Aug 11, 2009 | 1994 Lincoln Town Car

2 Answers

My fuel door doesn't open when i press the button


If you have a button it must be elec. if all other acc are working prob not fuse could be switch or mech at door

May 13, 2009 | 1998 Cadillac Catera

1 Answer

My right turning signal sometimes doesnt work. The light in the dash stays on, but doesnt flash. When this happens the front light stays on when the signal is applied, but the back one doent work. Ive...


  1. Turn 4 way (hazard) lights on check to see that all lights are flashing if rear is not flashing suspect bad ground since 4way usually goes through brake light.
  2. If everything flashes you may have a bad flasher relay find it replace it.
  3. If light still will not flash check light socket by removing bulb & looking for burnt melted contacts or plastic. You find any of these problems consider replacing socket.
  4. If you do not find any problems with socket use a cheap test prob connect alligator clip to metal ground near socket with bulb out turn on blinker carefully touch each contact inside socket when you find the right contact prob should light up & blink.
  5. If you cannot get prob to blink move prob ground to new location do step 4 again.
  6. If you still get no blink start probing wires coming into socket until prob lights working away from socket.
  7. Ground is on the side of the socket when you look in it.

Mar 08, 2009 | 1993 Dodge Shadow

1 Answer

2001 durango rear window defog light flashing


What code is it showing for the leak detection pump ? That pump along with all sensors on the vehicle can set more then one code , most can set half a dozen ! Circuit volt high , circuit voltage low , open , short to power , short to ground etc... You probably have a wiring problem , I'd say it's time to find a new mech. Plus you can not just swap PCM/ECM - engine computers , they need to be reconfigured an programmed . Or other problems will pop up . With the check engine light on codes or set !

May 22, 2017 | 2001 Dodge Durango

Not finding what you are looking for?
1989 Subaru Justy Logo

Related Topics:

605 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...