Question about 1998 Ford Escort

1 Answer

Starter where is starter located, procedure to replace?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 61,249 Answers

Next to the transmission, couple bolts and a few wires and the battery cable, very easy to change. Always disconnect the battery before doing this kind of work.

Posted on Oct 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the crankshaft position sensor located on a 2008 HHR 2.2 is that ecotec engine


My info says it is located above the starter motor. Info says to remove the starter.

The info also says you have to do a crankshaft variation relearn procedure. I can't help you with that procedure.

Nov 18, 2015 | Cars & Trucks

1 Answer

Where is starter located?


The starter is located on the lower side of the motor. Disconnect negative battery cable. Raise and support vehicle. Remove flywheel cover (s). Disconnect starter solenoid wiring. Remove starter mounting bolts. Remove shims and note arrangement for reassembly (if equipped). Remove starter assembly. To install, reverse removal procedure. Ensure shims are installed in original location (if equipped). Tighten fasteners to specification. Starter Bolts 35 Ft. Lbs, Flywheel Cover Bolts 89 Ft. Lbs, Positive Battery Cable-To-Solenoid Nut 89 Ft. Lbs, "S" Terminal Nut 37 Ft. Lbs

Jul 07, 2014 | 2001 Pontiac Montana

1 Answer

Starter relay location on 1999 durango 4x4


Its located in the under hood engine compartment fuse box.

There will be three same relays.One for fuel pump and other for horn and bit bigger one for starter controlling.

For more help regarding starter

CAR STARTER REMOVAL? TESTING


One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============

For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----

These help links will help.

Click the link below:-----


How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

-----------

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

How to replace Starter on Infiniti Q45?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

----------

2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

-----

Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html

----------

Oldsmobile starter solenoid replacement procedure?...

--------------------

How to replace Oldsmobile starter moor?

----------

Oldsmobile starter motor testing?

-------------

Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?

------------

These details will help.

Thanks.

Nov 28, 2012 | 1999 Dodge Durango

1 Answer

What are the steps to change a Kia Sedona Starter


The starter can be removed from under the vehicle. But before doing anything,first disconnect the negative terminal of the car battery.Do start the procedure with battery connected. The starter is located on the frame rail on the driver's side. Lift the car up on jack stands.Give proper support to the car before working under the car to locate and remove the starter.Now before removing the starter you will have to remove the upper intake manifold bracket .This manifold bracket is held by 4 screws,remove those screws first to loose the upper intake manifold bracket.Then remove the wiring connections from starter solenoid mounted on the top of the starter motor.There are two wiring connectors remove both.Both the wiring connectors are fitted by a nut.Remove both the nuts and loosen both the wiring connector.Now loosen the starter connecting bolts and remove the starter carefully from the engine compartment.In the reverse procedure reconnect the new/replacement starter and complete the procedure. ------- Keep updated for any more queries.Thanks.



Oct 14, 2010 | 2003 Kia Sedona

1 Answer

How do I replace the starter on a 2003 Camry?


1st to do, disconnect the battery and remove, also remove battery support , the starter is located between engine and transm. behind battery, now disconnect 2 wires from starter , loose 2 bolts 14mm wrench and starter will fall in your hand , note this procedure is for 4 cyl model , 6 cyl engine same

Jul 29, 2010 | 2003 Toyota Camry

1 Answer

I want to replace the starter on my 2000 ford expedition. How do i do that?


Unhook the battery cables, locate the starter, unbolt the wires going to it, remove the bolts holding the starter on, take starter off, reverse the procedure with the new starter.

Feb 02, 2010 | 2000 Ford Expedition

1 Answer

Location of the starter


PROCEDURE TO LOCATE AND REPLACE THE STARTER
Under the car, you will see a plastice cover between the main frame beam and the underside of the radiator. This will come off ( 2 Wing Nuts) for easy access to the starter. You can now remove the two wires that go to the starter solanoid. Now you must remove the splash guard on the starter.This is a cover plate that consist's of two screws. Now you can see two main bolts that hold the starter on. Remove these bolts and the starter can be removed from the underside of car.

Oct 06, 2009 | 2001 Oldsmobile Alero

2 Answers

Need to replace the starter on a 1994 Geo Prizm


starters are actually pretty easy. usually just 2 or 3 bolts holding it on. Just disconnect the battery first. Remove the bolts and the starter and then installation is reversal of removal.
Hope this helps,
Lee

Sep 15, 2009 | 1994 Geo Prizm

1 Answer

I need to replace my starter in my 2000 Chevy Blazer. I need help please.


Unhook battery cables from battery locate starter on underside of engine block on the passenger side three bolts to take out replace starter and reverse procedure fairly easy job!! good luck.

Aug 05, 2009 | 2000 Chevrolet Blazer

1 Answer

Starter replace


Your starter is below the air box, where air filter is. Remove air box and you will se the starter. Unplug battery. Remove nut (with 12mm wrench) which is connected to the starter, Nut is hidden under a rubber boot to prevent shorting out. unplug a single wire connector, which comes out of the starter solenoid. Starter is beeing held by 2 bolts. Remove 2 bolts, which you will be able to see and take out starter. Reverse procedure to install new starter. Reconnect battery.Start vehicle. The whole procedure should take under 1.0 hours.

Jul 26, 2008 | 1996 Nissan Maxima

Not finding what you are looking for?
1998 Ford Escort Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...