Question about 2002 Chevrolet TrailBlazer

1 Answer

License plate lamp not on? - 2002 Chevrolet TrailBlazer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

The bulb may be blown?
need more info thanks

Posted on Oct 15, 2008

6 Suggested Answers

eitan
  • 291 Answers

SOURCE: changing license plate lamps on the tracker

There's no need to take the whole back panel off to do it, the light cover on the bulb twists out, and it might take some elbow grease to twist it, then the bulb is easy to change.

Good luck,
Eitan.

Posted on Jun 10, 2008

alicantecoli
  • 21990 Answers

SOURCE: 2001 ford focus zx3

remove the whole unit its only a couple of 8mm nuts from the inside 15 min job including *** break

Posted on Nov 12, 2008

  • 2 Answers

SOURCE: license plate lamp

Left side lamp, with some soft force you twist it clockwise. Reverse action to reinstall.
Right side lamp, twist it counterclockwise. Reverse action to reinstall

Posted on Dec 31, 2008

michigan man
  • 3533 Answers

SOURCE: License Plate lights won't work

first of all i would get a 12- volt tested and turn the lights on take the new blub out and then test the sockets and no power test the wires behind the sockets if you have power then the sockets are bad or burn out replace if needed.

Posted on Feb 08, 2009

  • 1 Answer

SOURCE: can't get rear license plate lamp covers off

The manual says switch off the lights and disconnect the battery. Then "Open trunk lid. Press and slide license plate light outward and remove". The photo shows that there is a clip on the side of the light away from the center, and a notch that fits the body on the side towards the center. So what you are doing is pushing the light holder towards the side of the car far enough to compress the clip and get the notch past the metal, then the inner edge of the light hold should lift out. To install, just put the notched end in first and the press the outer edge until the clip snaps into place.

Posted on Aug 06, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the license plate light on a 93 geo metro


this is in the operators guide. (get one?)
R&R
  1. Disconnect the negative battery cable.
  2. Remove the screws from the license plate lamp assembly.
  3. Remove the license plate lamp assembly.
  4. Remove the socket from the lamp assembly.
  5. Remove the bulb from the socket.
  6. Installation is the reverse of removal.

Feb 04, 2015 | 1993 Geo Metro

1 Answer

Replace license plate light


what country? ( export below means , NOT USA)
its in the FSM
quote:
A single standard equipment rear license plate lamp unit is integral to the
license plate mounting bracket just below the left rear lamp unit on vehicles manufactured for domestic
markets. A bracket with two rear license plate lamps is located on the rear bumper directly below the
spare tire on vehicles manufactured for export markets.
and HOW TO: quote
1. Disconnect and isolate the battery negative cable.
2. Remove the license plate from the rear license plate bracket.
3. Remove the four screws (4) that secure the rear license plate bracket and lamp unit (3) to the four spring
nuts (2) in the rear body sheet metal (5).
4. Pull the bracket and lamp unit away from the rear body sheet metal far enough to access and disconnect
the body wire harness connector (1) from the connector on the back of the bracket and lamp unit housing.
5. Remove the bracket and lamp unit from the vehicle.
unquote the FSM.
Buy one for $20-

Aug 19, 2013 | 2010 Jeep Wrangler

1 Answer

How to replace License Plate Bulb '96 Jeep Grand Cherokee Limited


Hi Timmy:

Check this procedure from Repair manual...


LICENSE PLATE LAMP - REMOVAL
(1) Remove screws and license plate lamp visor from liftgate (Fig. 10).
(2) Remove bulb from lamp socket.

INSTALLATION
(1) Install a bulb in lamp socket.
(2) Position license plate lamp visor on liftgate and install screws (Fig 10).


4_28_2012_5_22_57_pm.jpg


Hope this helps.

Apr 28, 2012 | 1996 Jeep Grand Cherokee

1 Answer

How do I replace a rear license plate bulb in 2004 Jeep Liberty?


  1. Remove the screws that secure the license plate lamp assembly to the rear bumper fascia
  2. Pull the license plate lamp assembly down and out through the mounting hole in the rear bumper fascia far enough to access and disconnect the wire harness connector.
  3. Remove the license plate lamp assembly from the rear bumper fascia.

Apr 16, 2011 | 2004 Jeep Liberty

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

License Plate Lamp Replacement on 1999 Cadillac Eldorado ETC. Where is the access point for replacing the licence plate lamps?


Hello, remove the rear license plate, remove the housing where the license plate was mounted, now you can see how to replace the bulbs.

Sep 05, 2010 | 1999 Cadillac Eldorado

1 Answer

Change tag light bulb


  1. Remove two screws retaining the lamp to the rear license plate lamp shield.
  1. Rotate socket one quarter turn from backside of lamp and remove the miniature bulb (13466) .

  1. Install new miniature bulb into socket.
  1. Install socket in lamp .
  1. Secure lamp to rear license plate lamp shield with two screws and tighten to 2 Nm (18 lb-in).


    ak1473a.gif


    Item Part Number Description 1 13508 Rear License Plate Lamp Shield 2 14A583 Lamp Lead Wire 3 383356-S Nut (4 Req'd) 4 56000-S Screw (4 Req'd) 5 13550 Lamp (2 Req'd) 6 13466 Miniature Bulb (2 Req'd) A — Tighten to 2 Nm (18 Lb-In)

Feb 27, 2010 | 1998 Ford Windstar

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

License plate bulbs on 98 Park Avenue


License Plate Lights Removal & Installation 1997 – 2000 To Remove:

License/backup Lamp Assembly


76707d9.gif

  1. Remove the rear compartment lid trim. (if necessary)
  2. Disconnect the license/backup assembly connector from the body harness.
  3. While removing the license/backup lamp assembly from the rear compartment lid, disconnect the harness grommet from the rear compartment lid.
  4. Remove the license lamp housing from the license/backup lamp assembly.
  5. Remove the license lamp bulb from the housing and socket.
To Install:
  1. Install the license lamp bulb into the socket and housing.
  2. Install the license lamp housing onto the license/backup lamp assembly
    • Torque the fastener to 18 in-lb (2 Nm).
  3. While holding the license/backup lamp assembly, install the harness grommet to the rear compartment lid.
  4. Install the license/backup lamp assembly
    • Torque the fasteners to 53 in-lb (6 Nm).
  5. Connect the license/backup assembly connector to the body harness.
  6. Install the rear compartment lid trim. (if necessary)

Jun 30, 2009 | 1998 Buick LeSabre

1 Answer

How do I change the rear license plate light bulbs?


License Plate Lights Removal & Installation License plate lamp retainer clips
a555c7b.gif
To Remove:
Remove or disconnect the following:
  1. License plate
  2. Pin-type retainers and the luggage compartment lid trim panel
  3. License plate lamp electrical connector
  4. Lamp socket from the license plate lamp
  5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp
To Install:
  1. Install or connect the following:
  2. License plate lamp
  3. Lamp socket to the license plate lamp
  4. Electrical connector
  5. Luggage compartment lid trim panel
  6. License plate

Jun 06, 2009 | 2000 Lincoln LS

Not finding what you are looking for?
2002 Chevrolet TrailBlazer Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...