Question about 2006 Mazda 3

1 Answer

Dsc hi there dsc light is on tried using switch no success any suggestions how to resolve without paying mazda hundreds

Posted by on

  • Anonymous Dec 27, 2008

    same

  • azaroo Dec 27, 2008

    please tell me how you got it fixed

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Abs dsc module with a cost of £1700 from mazda...thats what fixes it..

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 mazda 6. The brake lights do not work. I changed the brake light switch and they still do not work. Suggestions?


check the fuse, check each brake light individually to see if they work. try a couple of wires from the battery to the lights to check them out. and finally, make sure brake light switch on pedal is adjusted properly so a slightly depressed pedal activates the circuit.

Jul 07, 2015 | Mazda Cars & Trucks

1 Answer

RX-8 & DSC


Hi Melissa,

I had a similar problem with my 2005 RX8 but didn't try using the DSC button. I had to have my engine rebuilt....I'm in So Cal and found a great private mechanic, are you local???

May 14, 2014 | 2005 Mazda RX-8

1 Answer

How do i change my signal switch in my 1993 mazda 929


Hi Shannon, befor you dive in and replace the indicator switch I would suggest you check the flasher unit. To replace the indicator switch you will need to remove the steering wheel (this usually means using a puller) Don't forget to punch match marks on the steering wheel and the column which must be aligned when assembling. Remove the steering wheel center cover. then the covers on the steering column Removed the screws (usually four) holding the stalk switch. don't forget to disconnect the battery and the wiring connection to the stalk switch. After replacing the assembly is opposite.to dismantling. Regards John

Nov 09, 2011 | 1993 Mazda 929

1 Answer

Hi all, Have recntly been getting the orange engine led alert popping up on the console from time to time on my 2004 grand voyager. (inconsistantly) Had a mechanic run through a computer scan and stated...


The light is on for a reason

The mechanic & yourself should have
continued on & worked together to resolve
the O2 Sensor rich condition

The E10 won't be an issue

You don't clean any type of sensors ,except
the MAF, no way to clean an O2,they get replaced,
front ones only at 100,000 miles or when the switching
count is too slow.

Any mechanic should be able to diagnose those issues

I don't understand the hundreds of questions we get
here every day. You took the first steps,then came home,
without requiring the mechanic to fix the issue and nothing else.

I hope he charged you for his time.
I wouldn't take out my scanner out of the
tool box until you were paying for my time

Jun 09, 2011 | 2004 Chrysler Voyager

1 Answer

How do you reset all the lights on dash battery abs etc on a mazda 1993 929


Hello and welcome to FixYa!


As a first course of action, I strongly suggest that you have the battery charged. It can be an indication of a weak battery or a faulty alternator. If the battery light still on after charging then the problem will surely be on the alternator itself. If that's the case the alternator should be replaced to resolve the problem.


You may try to reset it to by removing the positive battery connector, letting it sit for at least 5mins. then reconnect it again. This will reset the system and can get the battery light off.


Hope this helps and thank you for using FixYa! Have a good one!

May 22, 2011 | 1993 Mazda 929

1 Answer

Hi there my mazda 3 sport saloon was spluttering on tick over but no engine management light was on, got diagnostics done advised to change coil pack which i done, i then took the car out it started to...


Hi and welcome to FixYa!

As a first course of action I strongly suggest that you remove the positive battery connector and let it sit for at least 5mins. This will reset the car's computer and can resolve the issue. If it doesn't help then I suggest that you have the car diagnosed again.

There may be some sensors to replaced again. We really can't tell their break points and scanning the car will determine the fault codes.

Hope you find this information helpful enough and thank you for using FixYa! Have a good one!

Jan 27, 2011 | 2004 Mazda 3

2 Answers

After replacing starter on Mazda MPV,O/D light started flashing,Mech says it could be transmission problem,but the van was running fine before I took it in for repairs.Can you give me any suggestion


someone has broke or disconnected a wire somewhere under the car whilst changing the starter motor ,but what or where i couldnt tell you without having car on the ramp sorry

Nov 13, 2010 | 2001 Mazda MPV

Not finding what you are looking for?
2006 Mazda 3 Logo

Related Topics:

658 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...