Question about 1997 Geo Metro
Starter will not engage. Have checked battery as well as bought new battery , no help. took off the starter assembly and took it in to see if it was defective and it tests out fine. Have checked fuse under dash and that was not the problem. Tracker starts with no problem if you push it just a couple of feet. have checked battery connections and all of the starter wires. Pulling hair out now so frustrated.
You didnt tell drive line , so i guess.
89 is 8v motor TBI.
SO THIS IS THE PROBLEM
the start line , is bad at the clutch switch (5sp)
or if AT , it bad at the AT PRNDL SWITCH.
hhere see last photo.
Posted on Apr 30, 2009
To remove the radio:
Remove the ashtray by raising the armrest cover and removing the two screws at the rear of the ashtray. Slide the ashtray back and then lift it out. Be careful of the two front tabs, as you don't want to break them.
Reach below the wood console, where the ashtray front tabs were inserted. Loosen and remove the two wing nuts.
With a small, long flat bladed screwdriver, pry out the leather shifter surround. The leather shifter surround has a center chrome retaining ring, the leather surround, and then finally a black plastic surround. The chrome retaining ring has 3-4 tabs which are locked in below the leather surround. It depends on the year of the Jaguar. Probably the 95 has three, but maybe four. They should be at the front and rear of the trim piece (2 front and 1 back, or 2 front and two back) but I've seen then on the sides. The point is, you have to be careful with the screwdriver and find the tabs. The screwdriver should be slid between the leather and the retainer. Pull upwards on the retainer gently, and as you loosen the tabs, it will come out.
Remove the leather surround. Once the chrome retainer has been removed, it should be easy to work it out of the console.
Loosen the black trim ring gently as it has tabs as well, but they are visible once the leather trim has been removed. Lift it upwards out of the wood trim and pull it to the side out of the way. You don't need to disconnect the wires, just lay the black trim to the side.
Lift the rear of the wood console trim and gently, gently slide it back and up. It will try to hang on the leather console, and can be difficult. Patience is important, as the walnut on the ski slope cracks easy (really easy).
Once the wood console trim (ski slope) is removed, you should have a row of screws up the side of the center control panel, where the radio and AC controls are. There are four to six on each side, depending on what Jaguar used at the time, as the 95 cars mechanically are somewhat of a blend of the XJ40 and the XJ300. Remove these screws, and note any spacers that were behind them. These spacers get lost quickly, and cause the ski slope to sit awkwardly on the console.
The radio will slide forwards once these screws are removed. Remove the radio harness and the antenna lead. As the books say, assembly is reverse of removal.
Good luck, and let me know if you have questions. If you are replacing the radio, let me know as I have the harness wiring codes and can help you with that as well.
Posted on Jul 01, 2008
I had the very same problem with my 94 tracker and it turned out to be something simple. My check engine light had popped on after it had hit 100,000. I went through all of the suggestions that people had suggested (unplug battery......etc) and still to no avail. Searching the internet, I came across a website called suzukiforum.com and there, this guy was able to help me with my problem. It turned out to be a maintenance switch that kicks on every 50,000 miles. This switch is like a secret that the auto manufactures use to ploy owners of their cars to bring to the dealer and then rack up the dollars in unnecessary "repairs". The switch is located under the dash and can be hidden anywhere. From the assistance of the guy on the forum, he was able to send me photos of this damn switch and possible locations where it may be mounted. I found mine in about 5 minutes, where it was attached to the steering column. It's a tiny switch, that you slide up or down, depending on what position it is in upon finding it. If it's up, then slide it in the down position and visa versa. Once you do this, the check engine light will go off. Make sure you do not have the car running and you can even unhook one of the battery posts, just to make sure you don't hit anything while rooting around under the dash. Good luck!
Posted on Apr 30, 2009
If your lucky the code may have been written down in the manuel book. If it's not written down in the book or it's missing, drive to the chevy dealer that sells Geo trackers and the Service adviser can help you unlock the stereo by getting the information from the Vin number.
Good luck and hope this help. http://www.delcolockcodes.com/
Posted on May 23, 2009
first you remove the wheel then the break caliper then remove the locking hubs just remember to lay out the parts in order a special tool is called for but this job can be done without it you have to use a small cold chisel and a hammer to tap the large nut counter clockwise to remove, you can then remove the outer bearing and the rotor and hub assembly look on the back side reomve the bearing seal and inner bearing be sure to pack your new bearings with grease before you reassemble . takes less than an hour.
Posted on May 05, 2010
Tips for a great answer:
May 21, 2016 | Geo Cars & Trucks
Nov 26, 2013 | Geo Tracker Cars & Trucks
Jun 28, 2011 | 1992 Geo Tracker
Sep 14, 2010 | 1995 Geo Tracker
Jan 06, 2010 | 1991 Geo Storm
Nov 07, 2009 | 1995 Geo Tracker
Aug 10, 2009 | 1996 Geo Tracker 2 Door
Aug 11, 2008 | 1993 Geo Tracker
239 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: