Power Locks won't work completely using remote or interior switches. They "try" to unlock, I can see movement and hear a click under the steering wheel but they wont lock or unlock all the way. Tried resetingthe CPU via the remote, by holding down lock and unlock, horn chirped still no lock functions.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
2004 Nissan Maxima Key Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.
Close and lock all doors with the driver's side power lock/unlock switch.
Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.
Insert key into the ignition cylinder and turn to the ACC position.
Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.
If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver's side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).
Turn the key to the OFF position, remove keys from the ignition,
unlock doors using the driver's side power lock/unlock switch and open the driver side door.
2004-2005 CARAVANS HAD A SOFTWARE ISSUE IN THE BODY CONTROLLER..REMOVING AND REINSTALLING IOD FUSE IN UNDERHOOD FUSEBLOCK..THERE IS A SOFTWARE UPDATE FOR THE BODY CONTROLLER FROM CHRYSLER..TAKES ABOUT AN HOUR TO COMPLETE..AS FAR AS I KNOW,THEY ARE ONLY ONES WHO CAN DO THIS
this should be known issue at your nissan dealership, was a recall in most countries to replace all 4 door lock actuators. if the vehicle is out of warranty this may not apply.
The acuators are a sealed design and cannot be repaired, can only be replaced with new ones,
Im no professional but i did recently buy a 93 maxima and i have the same security alarm problem and my powered locks dont work at all. im taking off the door panel today to take a look and see if the alarm sensor is loose or damaged, if it is, ill probably just disconnect it. one thing i have noticed though is that when i hit the lock or unlock button, i hear a faint click from the dashboard area which im assuming is the solenoid on a transistor which would mean that the buttons work but the transistor isnt delivering power. Semi-Solution for Locks: Listen for very quiet click when you lock/unlock doors, if you hear it, uve got major work to do, if you dont, then take apart the door and check the switch connections. Semi-Solution for Alarm: take off the door panel and disconnect the sensor.
i would first look in the main wire harness unbdere the dash on the drivers side it leads into the door also there is a harness that leads up the steering column to your dimmer/turnsignal module in the steering column. if your door locks stop working it colud be the master switch control in the drivers door this is whjere i would look for the short
Hey, this might work.....get in truck, close doors, put key in ignition in lock position.....hold down the door lock button on driver side door control and wait for the lock control to be displayed on the information screen(odometer read-out).....it should say like lock 1, lock 2, lock 3, lock 4.....or something, I always reset mine to LOCK 1, to do this hold the odometer reset button on dash for a sec or two til it changes settings, then release, repeat till you get to LOCK 1, then quickly press and release odometer reset button to exit program, this is the function to lock doors over 15 mph and when out of park and to unlock doors when returned to park......yours' might be set to another function number....try it out, let me know if this helps.........good luck!