Question about Ford Laser

1 Answer

Car runs for 5 mins then cuts out

Buying a 89 laser, the seller says the engines stops around 5 mins. I can norrow it it down to a few problems but up for other sugeestions, the problem that I thought it could be are fuel pump, oil pump, ditributor cap-leads-spark plugs or the, how gease, mentle block on the name of it, but it's on the belt and charges up the battery. Any other thoughts

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 88 Answers

Check to see if it is a crankshaft sensor if applicable to this model.if not check to see if it is an electronic distrubutor.

Posted on Oct 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could cause intermittent engine stalling?


A bad MAP or MAF sensor could cause this type problem .

Mar 16, 2017 | 2007 Volkswagen Transporter 1.9

1 Answer

Starts and cuts off


serial number/keygen for registry reviver

Jan 28, 2014 | Cars & Trucks

1 Answer

My 96 ford taurus revs high when starting then works it way from 1500 or more down to 800 but fluctuates from 800 to a little over 1000. When putting car in rverse or drive from park engine revs up to...


You need to clean the IAC again and also the throttle valve and bore, use only CRC brand Throttle body cleaner. After they are thoroughly cleaned disconnect the battery for 5 min's and then drive the car in varying condition for a few days. If that doesn't cure the issue you have more serious problems and will need a scan tool to look into the readings from the MAF, TPS and ECT sensors. High idle cold start is normal then slowly dropping after a few minutes. I assume you never had a check engine light. Correct?

Mar 24, 2017 | 1996 Ford Taurus

1 Answer

1994 f150 6 cyl engine shuts down every 10 min restart after 5 min


Sounds like the module inside the distributor. Have to be replaced.

Sep 29, 2012 | Cars & Trucks

1 Answer

My nissan sentra 1987 stops, stalls and cuts off engine


Engine stall or RPM fluctuates at idle.

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Sep 28, 2012 | 1995 Nissan Sentra

1 Answer

I have 89 accord 6 cyln 3.0 vtec it just stops running wait a few min.then it will usually start its stops running about every 5 miles


this is going to be a bad ignition coil or bad distributor, i would replace the coil first but if the coil is built inside the distributor then replace the whiole unit but if its outside the dist then try replacing the coil first, then if it does the same thing then replace the distributor. this problem is very common with hondas, the internal modules heat up and die and then when they cool down it runs again ,hope this helps good day,

Sep 03, 2011 | Honda Accord Cars & Trucks

1 Answer

Morning or when engine cools down I have to run it for about 15min then it stop dead. wait for 5-10 mins, turn it on and runs again for 2-5 mins than stop again. wait for few more mins and on again, It...


dear sir
this can be problem cause of o2 sensor(lamda sensor) . in cold condition if we start the car some quantity of water can also came out through silencer and can stay at point of 02 sensor it is paced at silencer, ECU(Engine Control Unit) receive data from 02 sensor for Engine Firing . so replace it and let me know. thanks.

Sep 13, 2010 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

71288 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...