Question about 2000 Ford Focus

1 Answer

High beam I've crashed my car on the right side head on, i have everything fixed but the right high beam light doesn't work, low beam works. I have replaced the bulb twice. Help!

Posted by on

  • agleal Oct 14, 2008

    ok i check wires testing here and there for bad connections,could not fine anything. i did forget to mention that the high beam light indicator doesn't work either.

  • agleal Oct 17, 2008

    I found the solution to the problem. The plug that plugs to the headlamp the prongs were loose due to the impact of the crash. My brother and I were checking things out and I notice the prongs were not set in right, so my brother adjusted them and it worked. Of course I had to buy a few fuses. Thanks Fastboyz for helping.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

Check the fuses under the hood these headlamps are seperatly fused,
later
paul

Posted on Oct 14, 2008

  • paul erickson
    paul erickson Oct 15, 2008

    use your test light and check if you are getting power to your fuse for high right headlamp.

    depending if you have power there will determin where to go next.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

3 Answers

One low beam head lights will not work, high beam works though


check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

Dec 29, 2013 | 1997 Chevrolet Blazer

1 Answer

Left high beam head light has no power


your left head lamp needs replaced. thats all !!!!!!!!!

Feb 15, 2013 | 2007 Dodge Ram 2500 Mega Cab Laramie

1 Answer

I have a 96 Cavalier and my passenger side low beam does not turn on (high beams OK) & my horn doesn't work either. I've replaced the bulb with no luck. Any suggestions?


The light socket itself could be bad. If you turn on the lights and put a meter on it you can verify there is power at the socket. If not you still have to trouble shoot some more. No power at socket could be wiring that went bad or melted but you will have to remove the socket and test the wires themselves. No power at the wire bare ends you have to go back to the fuse distribution and check that. Low voltage sucks for this very reason. good luck.

Nov 12, 2012 | 1996 Chevrolet Cavalier

1 Answer

I have a 2002 Buick Rendevzeous. Sometimes the driver side low beam works, sometimes it doesn't. When it doesn't, the turn signal won't blink. It just stays dimmly lit. Right now, the low beam...


You have a bad electrical connection. Check the wiring harness and both sides of it's connectors for corrosion and or breakage. The connector terminals will become worn and corroded and the wiring sheaths a prone to weathering and become brittle. Replace or clean as needed.

Sep 04, 2011 | 2002 Buick Rendezvous

1 Answer

My light problem is i have low beam on right side no low on left side i turn highs on and right side goes out and high on left turns on then when back to lows beams and i pull turn signal to flash high...


If you have separate bulbs for the low and high beams(4 light system), if you pull the turn signal and hold it, all 4 lights will stay on until you release the turn signal. You need to replace the bright bulb on the right side and the low bulb on the left side. If your headlights only have one bulb on each side, then you will have to replace both of them to get everything to work.

Jan 04, 2011 | 2000 Ford Mustang

1 Answer

High beams dont work


Could be that your high beam light's are burnt out and need to be replaced. When you say the the switch is new you mean the lever on the stearing collum is new right?? Good luck

Apr 06, 2009 | 1998 Pontiac Sunfire

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...