Question about 1995 Jeep Cherokee

1 Answer

1992 jeep engine problem

Hello Mikey,
Thank You for respond. It is very difficult to define from where sound come. Top or bottom. For shure, it is louder at right side of engine. The cranck and rod bearings are instaled new. Also, no problem with loosing oil presure. It is constant. I forgot to tell, the "diesel" sound it's lost over 2000 rpm. And also, intensity of "diesel" sound is the same for this 2 years.
Regards Bajdzo

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 242 Answers

The oil clearance for a rod bearing was probably not done correctly allowing excess slapping. Check by unplugging your sparkplugs one at a time to see if the noise goes away. If it does, then the corresponding rod bearing is probably the cause. Check utube for videos of rod bearing noises and see if yours sound like those. That's how I found out my rod bearing was bad.

Posted on Oct 24, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Shift patterrn

5 speed 1st top left 2nd bottom left 3rd top middle 4th bottom middle 5th top right reverse bottom right
4wd 2wd top 4high one click down neutral shift to right then push down 4low bottom lowest point

Mar 26, 2014 | 1992 Jeep Wrangler

1 Answer

1992 jeep cherokee briarwood inline 6 4.0 4x4 need timing specs.

The ignition timing is non adjustable on your engine. Timing is totally controlled by the engine computer, responding to signals gathered from the engine sensors.

May 30, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

My jeep is making a really loud sound like an exhaust leak it's coming from the front end of the engine can anyone help

I would have the exhaust manifold inspected, a lot of times it cracks where the pipes connect. I am assuming you have a 4.0L. Then you would just need to change the manifold to fix the problem.
Thank you,

Feb 13, 2011 | 1992 Jeep Wrangler

1 Answer

Timing belt how do you set it

Make Shure Your Distributor T it on position 1 and from your Cam shaft make shure the natch is Top Position with little Triagle..Then Make shure you belt it correcly positioning on the bottom Sproket ..Then position top belt then slowly adjust the belt
till is stay on all the sproket adjust level Turn Slowly Engine conplete turn... then Check Cylender 1 for top piston corresponding to Distributor.. The T as to be aligned to pin 1 According Piston 1 for Ignition Start innitial Order 1-6-3-5-2-4

Oct 07, 2010 | 1997 Ford Contour

1 Answer

Gasoline smell from 1992 Jeep Cherokee 4.0 6 cylinder engine

Check Fuel pump seal at top of tank. Check carbon canister to see if it full of fuel and or carbon. You will have to disconnect the hoses to it and tip it upside down. Plugged evap hoses from tank to engine. Leaking fuel injector.

Sep 06, 2010 | 1992 Jeep Cherokee Sport

1 Answer

Just need to know what the torque specs are for 3.0 toyota 1992

This is for the 3VZ-E SOHC 12V engine, 2959cc catalytic. Sure its the same engine as in the pickup.----------
Stage 1 - 34nm--------- stage 2 - tighten by 90 degrees-------- stage 3 - tighten by 90 degrees-------- -------
the sequence is, with flywheel on your right, looking down on the engine...
--top row of bolts on top bank - top Left to top right bolts 1,2,3,4----------------- bottom row of bolts, on top bank - bottom left to bottom right bolts 3,4,5,6.------------ Top row of bolts on Bottom bank bolts 1,2,3,4------------- bottom row of bolts on bottom bank bolts 5,6,7,8------------ sequence is (top bank) 7,2,6,3,5,4,1,8-------- --------(bottom bank) 2,7,3,6,4,5,8--------
Hopefully this comes out tidy on the other end.

Jan 16, 2010 | 1992 Toyota Pickup

1 Answer

Located a chilton for 1998 jeep will it work for 1992 jeep cherokee. need to replace the alternator

Depends on which engine you have. If it is a 4.0L it should change out the same. This one must be removed from the bottom of the vehicle. Pay particular attention to the belt loosening technique in the maual which adjusts with the power steering pump.

Jul 10, 2009 | 1992 Jeep Cherokee Sport

1 Answer

1992 jeep engine problem

hello did you get your question answered?
how was the support

Oct 24, 2008 | 1995 Jeep Cherokee

1 Answer

1992 jeep engine problem

When you say new parts, does that mean cranck bearings and rod bearings?
Is the noise from the top or bottom?
Top noise could be lifters or rocker arms.
Bottom noise could be crank or rod bearings.
Oil pressure?

Oct 13, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides