Rear turn signal bulb

Quoting from link:

https://itstillruns.com/replace-lights-lincoln-town-cars-7660993.html

Tail Lights, Stop Lights and Rear Turn Signal Lights

Turn the Town Car's engine off, and open the trunk. Remove the trunk retainer if your Town Car is equipped with one. Put on the gloves.
Pull the carpet away in order to access the tail lamp assembly. Remove the three nut-and-washer assemblies with a socket wrench.
Remove the desired bulb socket by turning it counterclockwise, and then pulling it straight out of the assembly. Pull the old bulb out of the socket, and install a new bulb. All three lights use 3457AK-type bulbs.
Place the socket back into the assembly, and reinstall the three nut-and-washer assemblies. Place the carpet back into the vehicle, reattach the trunk retainer if necessary, and close the trunk.

https://itstillruns.com/replace-lights-lincoln-town-cars-7660993.html

Some of these are accessible through the trunk. There may be a piece of plastic or fabric behind the tail light assembly that can be emoved. Then usually the bulb and cable pugged into it are turned counter clockwise about a 1/2 turn to remove them.

The procedure to replace the REAR turn signal light bulb is as follows:- 1) There are three wing nuts on the inside of the trunk for each tail light. 2) Remove the piece of plastic just inside the trunk where the latch is. 3)Then remove the two thumb screws that the cargo net is attached to and the piece can be pulled up. 4)Them pull the carpeting away from the area where the tail light is located. 5)properly remove the three thumb screws. 6) Keep the bulb handy so you can fit the new bulb as the old bulb is removed out. The procedure to replace the FRONT turn signal is as follows:-- 1) First remove the front headlight assembly.And the bulbs . 2) Open the hood to remove the headlight assembly. 3) Pull the headlamp assembly straight out from the vehicle (moving the headlamp up and down slightly may help to remove it easily). 4) Front turn signal is located below the headlamp assembly (turn/parking lamp on top and the fog lamp is below it). 5) Then turn the bulb socket 1/4 turn counterclockwise to remove it from assembly. 6)Then pull the old bulb from the socket and replace it with a new one. Thanks. you can rate this solution and show your appreciation.

First,

1. Turn the engine off and open the hood. Pry up the two fasteners from the radiator air baffle with a flat head screwdriver. Move the baffle to the side to access the top of the headlight case.
   
2. Step 2 Pull up the two metal rods behind the headlight case. These secure the case to the car. You may need your pliers to pull them up.
   
3. Step 3 Gently pull the headlight case out to access its rear. On the rear, you will find several black dust covers. Twist off the dust cover closest to the fender (the outward dust cover) to access the turn signal bulb.
   
4. Step 4 Turn the bulb module counterclockwise to release it. Unplug the electrical connector from the bulb module. Connect the new bulb to the electrical connector (don't touch the glass with your hands; hold it by the plastic piece). Insert the bulb module in the turn signal housing, turn it clockwise and screw the dust cover back on.
   
5. Step 5 Insert the headlight case in the mount. Push the pins back down to secure it. Position the radiator baffle in its place and insert the fasteners.
   
Rear Turn Signal Bulbs
6. Step 1 Open the trunk. Remove the net from the side mounted wing nut (on the side with the faulty turn signal). Twist the wing nuts (there are two per side) counterclockwise to remove them.
   
7. Step 2 Peel the carpet layer back to access the rear signal lamp wing nuts. Twist these wing nuts (two per side) counterclockwise to remove them and release the rear signal.
   
8. Step 3 Carefully pull the rear signal assembly away from the Impala. The rear turn signal is the inner bulb (closest to the trunk). Press the tab on the bulb module and turn it counterclockwise to release it from the rear signal assembly.
   
9. Step 4 Pull the old bulb straight off the module (don't twist). Insert the new bulb in the module. Depress the tab on the connection and insert the module back in the assembly. Twist it clockwise.
   
10. Step 5 Insert the rear signal assembly. Re-attach the assembly's wing nuts and push the carpet layer back in place. Tighten the other two wing nuts to secure the carpet layer and reconnect the cargo net
    

Should be accessable from inside the trunk, behind the panel. Turn bulb holder counter clock wise, and remove from socket.

in your trunk you should see 4-6 plastic screw fasteners unscrew these the whole assembly will come out take the bulb that bad out turn counter clockwise replace bulb reverse the process. (fyi)your screw fasteners may be behind the fabric that lines the trunk just pull this out of the way.

Open the trunk, look for the wires running to the turn signal, it will usually twu\ist out or allow for entire turn signal box to be removed.

Open the trunk, behind the light you will see a plastic wing nut, remove it.
Then pull the carpeted trunk liner away and you will find 2 more plastic wing nuts. remove both of them and the wireing harness. the lamp will now com off the back of the car. twist the bulb base out and replace with new bulb.

You can go to www.chargerforumz.com with any other charger questions. use me Sandman2053 as a refrence. its FREE to sign up

remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

it's in the trunk behind the materail in the trunk