Question about 1993 Toyota 4Runner

1 Answer

Driver Side Mirror

Driver side electric mirror inside housing is coming loose how do I tighten?

Posted by on

  • Anonymous Mar 14, 2014

    Mirror housing is loose and swigs freely. Possible to tighten?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 F250 mirror loose, how to tighten?


the triangel cover on the inside towards the front of the door. pop it off and youll see three 10mm bolts that hold the whole housing to the door.

Apr 11, 2014 | 2001 Ford F-250 Super Duty

1 Answer

Tighten side mirror


If the mirror housing is loose and nothing has hit it and broken the mounting to the door frame, yes. If it is the glass part that is loose and it is a electric or manual mirror, something has damaged it behind the glass replacing it will fix problem.

Dec 07, 2013 | 2007 Lincoln Mark LT

1 Answer

Passenger side mirror is loose, how do i tighten it?


If the mirror housing is loose where it attaches to the door panel, you will probably have to remove the inner (inside the car) door panel to gain access the 2 or 3 nuts or bolts that secure the housing to the door and tighten them.

Sep 03, 2010 | 1999 Volkswagen Beetle

1 Answer

1994 chevy silverado driver side mirror is loose


try removing the black cover that wraps out from the door to the mirror just be carefull.....plastic ****.

Apr 25, 2010 | Chevrolet Silverado Cars & Trucks

1 Answer

The glass in the driver side rear view mirror is loose. how do you tighten it up?


The driver and passenger side mirrors have a small rubber plug in the bottom center of the mirror housing. Remove the plug and there is a phillips head screw holding the mirror assembly. Tighten this screw about 1/8 turn and it will keep the mirror from moving around. If you remove the screw you can remove the mirror and drive motors. Use a bit of thread-lock to keep the screw from loosing again. Reinstall the rubber plug.

Jan 30, 2010 | 1991 Toyota Previa

1 Answer

Power mirrors are loose, how do i tighten them?


Hi, if the complete unit is loose you will find bolts on the inside of the door just above the door panel behind a cover (usually a triangular shaped cover), that you will have to tighten. If the mirror glass is loose you should find a hole underneath the mirror housing where you have to put a screw driver in and tighten the screw on the inside to secure the glass.

Jan 17, 2010 | 2003 GMC Sierra 1500

1 Answer

Driver side mirror loose how can i tighten it


Most mirrors have a removable cover just on the inside of the door. If you look closely where the mirror meets the door on the inside should be a snap in place cover or three screw holes with snap in covers that you remove and then use a screwdriver or small socket wrench to tighten the screws or bolts.

Joe

May 20, 2009 | 1993 Saturn SC1

1 Answer

99 explorer drivers side mirror vibrates


are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

  1. Remove the front door trim panel; refer to Section 501-05 .
  2. go to car-part.com for a used mirror. Page with * is cheapest seller.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
------------------------------------------------------
f9d70e9.gif
----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
4d9527f.gif

Apr 12, 2009 | 1999 Ford Explorer

1 Answer

2006 ford focus driver side mirror (electric)


Not that hard on this model.Here is a pic of the mirror and the removal and installation proceedure.

http://i253.photobucket.com/albums/hh43/chuck943/N0025797.gif

  1. Remove the exterior mirror trim cover.
    1. Release the retaining clip.
    1. Disconnect the exterior mirror control switch electrical connector.
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the exterior mirror bolt.
    • To install, tighten to 11 Nm (8 lb-ft).
  1. If equipped, remove the exterior mirror screw.
    • To install, tighten to 2 Nm (18 lb-in).
  1. Remove the exterior mirror.
  1. To install, reverse the removal procedure.

Mar 02, 2009 | 2001 Ford Focus

1 Answer

1988 jeep cherokee drivers side mirror


It sound like some of the control cables have come loose. Check that out and also check the mirror mounts to make sure they are tight. the control cables should be lubricated once in awhile too.

Feb 12, 2009 | 1988 Jeep Cherokee

Not finding what you are looking for?
1993 Toyota 4Runner Logo

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...