Question about Hyundai Sonata

1 Answer

Cranks don't start. Computer reads crank shaft position sensor

Posted by on

  • Anonymous Mar 15, 2014

    MECHANIC SAID IT WAS TURNED INCORRECTLY NEED DIAGRAM

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 56 Answers

Get a chilton's repair manual for your car so you can locate the crankshaft position sensor and replace it . it's bad and the car will NOT start or run without a good one in it. but don't buy one from autozone, they are the worst with electrical parts. i would buy one from the dealer, it's usually a 12 month/12,000 mile part warranty. If you are not a mechanical person and don't think you can repair it yourself, have it towed to a reputable shop and ask them to use dealer parts.

Posted on Oct 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Changed alternator turns over still wont crank


Check some fuses or see if you are getting any kind of spark. Spark at the plugs or injectors.

Apr 14, 2015 | 2004 Dodge Stratus

1 Answer

My 2002 infiniti q45 turned off while sitting at a traffic light. Tried to start itbut in won't start. Diagnosed it and It showed cam shaft position sensor circuit malfunction. .code P0340...I replaced...


Did you check your fuel filter? Did you have a shop install the sensors? If they are not positioned in correctly, it won't work. Have you had your fuel pump checked as well? That's in your fuel tank. With this high end car, there may be a reset code as well.

Feb 21, 2015 | 2002 Infiniti Q45

1 Answer

Car cranks wont start


run fault codes to find the faulty sensor that is not allowing the injectors to work. It may be a cam position sensor . Check that the cam shaft is turning ( broken timing belt.)

Jan 20, 2014 | Cars & Trucks

1 Answer

Car cranks but does not start


The PGM relay is in the fuse box near the engine battery.

Jul 06, 2013 | Cars & Trucks

2 Answers

My pt cruiser just quit driving down the road one day put it on computer said coil pack was bad changed it still wouldnt start hooked back up to computer said cam sensor was bad changed it still wouldnt...


On this type of vehicles' "Diamler-Chrysler" for some reason the Crank and Cam sensor go bad at the same time but it will still tell you its either one or the other, if you are still getting the Cam sensor trouble code, try replacing the Crank Shaft Position Sensor, I just had a Dodge vehicle with the same problem but in reverse, it kept saying Crank Sensor but it turned out it was the Cam Sensor. Good Luck.

Sep 10, 2010 | 2002 Chrysler PT Cruiser

1 Answer

Was driving down highway and it just quit running it cranks but won't fire


Jeeps have a problem with the crank shaft position sensor. It's located at the back of the engine where the transmission meets the engine, The part is about $50 but can be replaced easily by anyone. The sensor works off the crankshaft to know what position it's in and if the sensor cannot read off the shaft then the engine will not fire because it has no idea what position everything is in to start the engine, If you have trouble finding this part, I have a manual on this car an would be glad to scan the info and send it to you through e-mail or here. Good luck.

Aug 14, 2010 | 1995 Jeep Grand Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

2 Answers

My alternator belt broke i fixd it now my car wont start it cranks but sounds funny


I am not sure where the crank position sensor is on your car but when the alternator belt broke on my Buick it trashed the crank sensor that is located next to the crank shaft pulley. The computer needs the crank senor to know the position of the crank shaft. If the sensor is bad the car will not start.

Nov 30, 2008 | Kia Sephia Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...