Question about 1999 Chevrolet C1500

4 Answers

Chevy 5.7 17 bolt heads tork specs

I have a 1999 chevy suburbun it has a 5.7 vortech engine with 17 bolt heads I need to know the tork specs on the head bolts

Posted by on

  • 4 more comments 
  • Anonymous May 07, 2009

    head bolt torque specifications 99 tahoe 5.7 vortec

  • Anonymous Mar 12, 2014

    2003 5.3 litter v8 head bolt torqe specs

  • Anonymous Mar 13, 2014

    need torgue specs for transmission pan bolts

  • Anonymous Mar 14, 2014

    bolt down head on a 5.3 chevy avalanche

  • Anonymous Mar 24, 2014

    torque specs on the head bolts on a 1998 chevy lumina 3100 v-6

  • Anonymous Mar 24, 2014

    torque specs

×

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 360 Answers

Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb

Posted on Oct 13, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 231 Answers

First torque them all to 22 foot pounds
next : short bolts turn them an additional 55 degrees
medium bolts turn them an additional 65 degrees
long bolts turn them an additional 75 degrees
hope that this is helpfull to you and that you take the time to rate this solution.

Posted on Oct 13, 2008

  • Fred Kenmuir Oct 13, 2008

    Lower intake manifold bolts

    step # 1) 27 inch pounds

    step # 2) 106 inch pounds

    step # 3) 11 foot pounds



    Upper intake manifold bolts

    step # 1) 44 inch pounds

    step # 2) 88 inch pounds

×

I need to know the tork specs on the intake not the heads

Posted on Oct 13, 2008

I need to know the intake manifold bolts tork specs

Posted on Oct 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the tork spec on 1998 Buick 3800 block for the cylinder head.


hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.


0996b43f8021ae77.jpg

Jun 18, 2011 | 1998 Buick LeSabre

1 Answer

Changed heah.need to know how to put timing belt back on.and what is the head bolts tork spec.


Here is the Timing Chain installation procedure: http://www.4shared.com/document/M8reUm2d/1992_Toyota_4Runner_Timing_Cha.html


Head Bolts Installation


Install and tighten the head bolts gradually in three passes in the sequence shown. Torque the bolts on the final pass. Torque: 78N-m (800kgf-cm, 58ft-Ibf)
pctech1_29.jpg

Mar 06, 2011 | 1992 Toyota 4Runner

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

1 Answer

I need the engine torque specs for 99 chevy malibu. like the head bolt torque sequence and rocker bolt torque sequence


99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Mar 12, 2010 | 1999 Chevrolet Malibu

2 Answers

I have a chevy 283 v8, I have replaced the head gaskets however i dont know the tork sequence or spec to reinstall them, also the rocker bolt spec


Spark Plugs: 20-25 Cylinder Head Bolts: 60-70 Intake Manifold: 25-35 Exhaust Manifold: 18-22 Rocker Arm Shaft Bracket: none Rocker Arm Covers: 25 (inch/lbs) Connecting Rod Cap Bolts: 30-35 Main Bearing Cap Bolts: 60-70 Flywheel to Crankshaft: 55-65 Vibration Damper or Pulley: Pressed on

Nov 03, 2009 | Chevrolet Impala Cars & Trucks

1 Answer

Need the tork spec for the rods, mains, and cam 99 cav 2.2


go to any good parts store and get or order
a repair book specific for your car that
will have the info that u require

gl G

May 03, 2009 | 1999 Chevrolet Cavalier

1 Answer

Torque specks


hi 1999 chevy malibu head bolts 1-8 40 ft lbs bolts9-10 30 ft lbs tighten all bolts an additional 90 degrees

rod bearings 18 ft lbs plus additional 80 degrees

head
top row of bolts 9 3 1 5 7 bottom row 10 6 2 4 8 from left to right

Feb 12, 2009 | 1999 Chevrolet Malibu

1 Answer

Replacing head after repair bent valves need tork specs for head


if interested i can e-mail you a diagram of the torque sequence and torque values just did one this weekend.

Nov 14, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
1999 Chevrolet C1500 Logo

3,701 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...